Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Cluster comes with 147Km on odo. Just goes to show how far wound back most cars are that are sold here (assuming fairly typical distance travelled). Having said that, I don't particularly want my car having an extra 50K added to the odometer. Then you got to explain to everyone who looks at it... lol

well your probably aware that 87-90 degrees of water is normal for our car.

its just how thin the radiator is and the load on it.

bigger radiator to take the load for winter will far out do the thermostat, especially if it ends up being too cold and keeps the car is a cold start map lol

Don't confuse the Nismo thermostat (which doesn't do that) with the Mishimoto thermostat (which does do that).

Bigger radiator would be more beneficial in the summer you'd think, yes?

Don't confuse the Nismo thermostat (which doesn't do that) with the Mishimoto thermostat (which does do that).

Bigger radiator would be more beneficial in the summer you'd think, yes?

yeh but there is a lower temp nismo thermostat available. isnt there?

i duno what your trying to get at

I thought Nismo was lower than stock, and Mishimoto was lower again.

Thought I read a thread on here where Scott fitted the Mishimoto and it was too cold and stuffed the car around, but I haven't seen much on the Nismo?

I run a 54mm race radiator and the Nismo thermostat.......no problems with my car with normal running in winter.....it hangs around 85 to 89 in traffic and about 84 on the freeway on hot or cold days....pretty sure from memory it was the same in summer.

On the track it dropped down 2 degrees and ran a perfect 83 degrees the whole time.......makes me think that it would do about 85-86 degree's in summer on the track!

Edited by Jetwreck

I run a 54mm race radiator and the Nismo thermostat.......no problems with my car with normal running in winter.....it hangs around 85 to 89 in traffic and about 84 on the freeway on hot or cold days....pretty sure from memory it was the same in summer.

On the track it dropped down 2 degrees and ran a perfect 83 degrees the whole time.......makes me think that it would do about 85-86 degree's in summer on the track!

Ahh too late sold it to Whiteaxis...LOL

yeh but there is a lower temp nismo thermostat available. isnt there?

i duno what your trying to get at

Below would be what I am getting at, thanks Ryan.

I thought Nismo was lower than stock, and Mishimoto was lower again.

Thought I read a thread on here where Scott fitted the Mishimoto and it was too cold and stuffed the car around, but I haven't seen much on the Nismo?

You don't really hear anything about them because the Nismo just works.

no you can legally change them over and report the change, to be honest i dont know whats involved. mine was only a few thousand off so i didnt bother

Mine has 25,000k's on the odo now. ;) I still have the original I can give the next buyer but I don't think they will care. Its obvious an aftermarket Nismo dash will change the K's isnt it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...