Jump to content
SAU Community

Recommended Posts

You are dicking yourself in terms of performance and reliability.

Save your money and highflow the stock turbo to run the 12 instead of running dual maps so you can run some magical sauce only to blow the rear wheel off the turbo which might take your motor with it.

plus guys before you get all excited US fuel octane number is measured differently to ours (they quote an average of RON and MON we just quote RON which reads much higher than MON ratings). their 91 octane (AKI) fuel is somewhere around our 95RON fuel (not quite as good as our 98 RON but nor far off).

as for the OP, there is no set formula. you need to tune it for the new fuel and see how much boost and timing it will take before it either stops making more power or it knocks.

also why only 12psi? with no more boost you will struggle to get much more power. if it's only for drag runs, wind it up a bit. even just another 3psi of so will give some decent gain.

I've read that 12 psi is the most you want to run on the stock, ceramic turbo wheel. just not looking to hurt the engine. I need that bottom end to hold up to the GT35 when funding is available.

So far my best is a 13.30 @107. 12 psi 11.8ish afr's. this is with a 2.0 60'. I have some mickey thompson et streets now. shooting for a high 12's, maybe mid 12's on race gas.

I've read that 12 psi is the most you want to run on the stock, ceramic turbo wheel. just not looking to hurt the engine. I need that bottom end to hold up to the GT35 when funding is available.

So far my best is a 13.30 @107. 12 psi 11.8ish afr's. this is with a 2.0 60'. I have some mickey thompson et streets now. shooting for a high 12's, maybe mid 12's on race gas.

If you are keeping the bottom end stock (i.e. not rebored and forged etc ) a GT3076 will give you all the power you can handle - 300 - 330kw. A GT35 is good for a lot more than the stock RB25 can cope with.

It's not the boost that kills the turbo, it's the excess shaft speed.

US fuel also contains more benzine and other products that make it more knock resistant for the same 'octane rating'.

Your going to need a fair bit more power to run consistant mid 12's from a 13... Id spend some time taking weight out of the thing first. Then a ethanol tune.

Or nitrous.

Cheers

Justin

I eventually plan on building up an engine for the car. the GT35 is just so I dont outgrow the turbo.

My car with me in it is under 3000 pounds, I should be able to shave a quarter second off the 60' foot time, I will be launching off of a two step at 5000. so a quarter second off the sixty has always been, and SHOULD be good for a half second off the big end. thats 12.80 without race gas.

I'm mainly just curious how much timing I can add for the race gas. Ive heard 6 degrees, 8 degrees??? also would I need to go to a hotter plug???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...