Jump to content
SAU Community

Recommended Posts

waiting on a reply from cj motors off ns.

they say they have bride type rx rails in stock and genuine for 279 each.

so once i get a price for freight and confirmation of stock on hand ill be ordering a pair from them i think.

was gonna get the grizzly imports power rails. but they wont send me a pic of the actual rail just the generic pic they have online.

and its not the right rail so i dont trust em. rather pay the extra money for somethin i know will be the right stuff

so got laurel back from boostworx. didnt make the power i was hoping for but apparently there is a restriction believed to be my supposedly high flow cat..

its makes awesome mid range power (it made an extra 45kw through the mid range) on 15.5psi but drops down to about 13psi up top because of the restriction leading to a total figure of 174.3.

next step is decat pipe and some new coil packs as they show signs of arching out.

overal very happy with it now. drives a shit load better off boost and comes onto boost quicker and harder. :)

heres a pic of the dyno graph.

20120828_173016.jpg

Edited by DannyC33

gap is set to 0.7 currently.

havent given it a full bootful yet. but from 4000rpm it really moves quite quickly up to 6000rpm and speedo starts tickin over quite quick haha.

at 3000rpm its makin about 8psi on full throttle in 3rd gear. but had to back off for traffic.

yeah but you gotta do what you gotta do.

if it turns out to be my car causing the issue ill get a new proper high flow cat.

it is good fun, but i want 200 haha.

bride rails rocked up today, i missed the courier though. will be ringing them tomorrow to see if i can get them delivered to work.

so i tried to organise to get the courier to deliver the rails to my work..... apparently this isnt possible because they dont have authority to do this.

even though i gave them my name address and the tracking number.

anyways i went and picked the up. 35min drive. each way. ohwells.

20120830_160709.jpg

20120830_164856.jpg

and finally installed!!

they are low. not excessively and seem to be on a sloping rail. the closer to the wheel you sit the higher it gets haha.

handy if any short people drive it i spose.

20120830_175725.jpg

sorry bout the shit pictures. camera phone plus literally just finished bolting them in haha.

LOL yeah I'm in the US and they are everywhere here, I'm actually just gonna make my own so they can sit lower since I'm 6'7, not that hard to make.

I have a set from a friend but just haven't gotten around to mocking them up yet.

The stock seat are pretty comfy so far so they are just on the back burner while I take care of the other things on my list.

Thanks for the look out anyway!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...