Jump to content
SAU Community

Recommended Posts

What makes 180rwhp? My stock turbo skyline was making 193rwkw on 12psi and is a very quick car. How much does the M3 weigh? It is a fairly big car. Both my skylines produced more torque also. In that graph that V8 is making 259ft pounds of torque. My old skyline made close to 320ft pounds and the current one is pushing more than 500ft pounds. I'm sitting on about 700nm and that is out of a small 2.5L 1.3 ton car. And I don't just peak that torque

Stock R33 GTSTs make around 180rwhp. They run 7psi, smic etc.

M3 E36 Evo is 1500kg. R33 GTSTs are 1390kg, so yeah, 110kg less.

E92 M3 is 1620kg.

700nm of torque? lol. Merc C63 AMG BLACK has 630NM.

Edited by 10 4
  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yeah. Dyno torque readouts, unless setup properly, are usually completely worthless since the figures are way out.

exactly. i've seen plenty of dyno readouts from small cars that are higher than the quoted figures for v8's and things like the xr6t. there's no way a 2.5L turbo 6 making under 200rwkw is making 30% more torque than a 4.0L turbo 6 that makes 270kw at the fly.

a rb25 making around 200kw would probably be making no more than 400nm at a guess, probably less though.

Yeah you aren't making 700nm of torque.

I exaggerated a little, its closer to 670nm.

What good is a dyno if it can't read proper figures? No one can tell me there is going to be a massive difference from the readout to an actual engine figure. If this is the case, why is the kw or hp anything to go by?. It was on dyno with two people in the car and about 50 - 60kg of led in the boot, two straps holding it underneath and still we were losing traction on the dyno. Tao made close to 600nm on with the same turbo in his car on a hub dyno.

I'm making about 300rwkw.

Edited by SargeRX8

It’s because the dyno operator rarely dials in the gear ratio/final drive/wheel diameter etc, I've had the same argument with actual tuners before, yarning about excessive torque figures.

But if you get the RPM at which you make the peak torque figure and get the power figure at that point (using the graph) then use the equation [Torque (N.m) = 9.5488 x Power (kW) / Speed (RPM)] that will give you your actual torque figure at the wheels.

Or just use this calculator;

http://wentec.com/unipower/calculators/power_torque.asp

530nm according to that calculator. According to my dyno sheet my tractive force is 1340 lb or something at 132mph.

And just because that AMG has that much torque doesn't mean shit. There are a bucket loads of cars which will deal out more power than that mercedes for no where near the price they ask for that car. What is your point? My brothers rotor makes close to 900rwhp cost 30k. You can get a 2jz spend some money on it and get massive power and torque. Doesn't mean shit when you point out the amg.

If the above calculator is right then cool, my car is only down 100nm of torque and doesn't have a engine which probably weighs more than my car.

i believe they are abit of a boat, but in all honesty, change suspension and do ur part in getting it stiffer then that will be gone. then powerrrrr it ;)

As for the camry yeah dw about what he said, u like ur car then dont worry about what people say

However, Aurions is the new model up from the avalon, and is completly different to the camry in power, looks sorta similar, dont misjudge who to run haha, cus aurions are machines

and doesn't have a engine which probably weighs more than my car.

LOL... WAT?

If the engine gets heavier, the car gets heavier... Secondly, the RB engines are f**kING HEAVY!!! My engine that is more then twice the size of the RB25 is around 50KG lighter...

Bloody cast iron crap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Apologies for the long post, but needed somewhere to lay out the entire timeline of events and actions taken:   I've got an 89 GTR with a R34 RB in it. It's been running great all year, driven probably 500KM in the last month. It's not my daily driver, just a weekend fun car.    Build info: R34 RB26 - HKS 2.7 stroker kit, HKS adjustable cam gears, HKS turbo upgrades, Trust intercooler, R34 factory DENSO 440cc injectors, JUN chipped/tuned R32 ECU. All of this work was performed in Japan back in 2019.    Thursday 10/2/25 - It's a nice day and decided I'll drive it to work, I start it up in the garage and I notice it took a few extra cranks and sounded a bit funny. I figure maybe it was just because it was a pretty chilly morning. I pull it out into the driveway to warm up a bit before leaving. As I leave the driveway, it feels very off and sounds like a misfire. I pull it back in the garage to deal with after work and take the daily to work. I was able to diagnose it as a cylinder 5 misfire with the old spark plug test (unplugging each plug until a sound change with the engine running). I take off the whole ignition system, ignitor, plugs, spark. *Important note, it is still on the R32 ignition system with the separate ignitor system. I test each system with a multi-meter and nothing presents as a smoking gun. I put it all back together and it starts up no issue. I go ahead and order the PRP R35 ignition conversion kit. It should arrive today (10/13/25)   Friday 10/3/25 - Another nice day, car starts up great and drives great all day. Very pleased that everything seems to be OK   Sunday 10/5/25 - Decided I'll take it to play some golf, load up and drive to the course about 25 minutes away. Drives wonderful the whole way there, I pull in the parking lot and the engine completely comes to a stop. I do not recall if it sputtered at all, but just remember all of the sudden the engine was off. I roll it into a parking spot, try to crank it back on and nothing.  It'll crank and crank and not even try to start. End up getting it towed back to my house and push it up into the garage.    Items I have checked: Fuel in the tank Fuel Pump relay Fuel pump fuse  Spark Plugs & gap Coil packs Ignitor    I know the cylinders are getting fuel as the plugs smell like fuel after a start attempt. I tried spraying starter fluid into the manifold and cranking and not even a sputter.    I decided to do the live CAS test (removing the the CAS, ignition on and spinning the CAS stalk to see if the injectors pulse and spark is active). All of the injectors were pulsing and I have spark at the plug. The half-moon end of the CAS did seem very loose, I'm not sure how much play is supposed to be there, but it was more than I expected. There was no in/out play of the shaft, just the tip end that is pinned on had quite a bit of play.    CAS Play video   When I put the CAS back in, I stupidly did not re-time the engine. I know I need to do that tonight, however, I do not think it will start given it seemingly was not the issue. My plan is to do the PRP R35 coil kit and retime the engine at the same time.    I plan on ordering the Haltech Nexus Plug-in ECU once they are available again, but ideally would like to get this sorted before firing the parts cannon at it and potentially adding more variables.    Anything glaring that I am missing here, I'm a bit at a loss?          
    • Get it on a dyno. Get something logging Consult. Run it up and find out what is causing it.
    • Looking for a plenum for rb25 de+t neo  Not looking to push much power maybe 300kw at the wheels, is there much difference in flow for Freddy “Greddy style” compared to original Greddy or options like Proflow or Otaku garage?    I won’t be porting the de Neo head for now as I think it’ll be fine 280-300rwkw but appreciate the help and any experiences anyone has between them and any advice. Thanks  Looking at this plenum for now below 
    • engine wise almost no mods: stock ecu Greddy front mount intercooler Greddy forward facing intake w R33 TB stock fuel system, stock injectors, rail etc. Kakimoto racing hyper 3 inch exhaust system Apexi intake filter New NGK –R BCPRES (.8 gap) plugs  
    • Nice one @Pac - looks like a fair few 1600's there! 
×
×
  • Create New...