Jump to content
SAU Community

Recommended Posts

benm i just got the tyres the same day i went to the track so i didnt get time for practise with the best launch technique. Plus my car is auto so i cant do big clutch dumps so i was stalling it to about 2.5 - 3k then flooring it. ill get my alloy bushes fitted and practise some more and ill see how i go.

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

Hi Matt, road tyres take at least 500 k's to "run in".  They give off oil and other lubricants used in their manufacture.  So they have to heat cycle a number of times to make sure the "slippery stuff" is cooked off.  When they are new the more you "smoke em up" the worse the grip gets as buckets loads of lubricants all come out at once.  So run them in.

This is spot on. I put new tyres on yesterday and decided to launch them hard right away. They were absolutely appalling so I backed off. When I got home there was a layer of oily residue around the paint work of the rear wheels, evidence that "lubricants" had come off at once. It looked very similar to when I got off the skid pan!

They guy at the tyre shop said they'll need to be "scrubbed in" for about 100-200km before they start to stick properly. I've done about 90km since and the difference is already amazing when compared to yesterday's first efforts.

You can check my new rims out by looking here :)

i thought i would bring it up as some of the monkeys in the tyre shops pump the tyres up so hard its silly, i ran speedway for ten years and found tyre pressure very importane part of tune car set up and after watch some serious dragster it seems to be true in drag racing .

i found it had a huge influnce on my gtr launching and ran a 1.7 60foot on a lighty tune r33 gtr

I want GRIP, my mate has 223rwkw and can rip it off the line and doesnt lose traction through gear changes, he had federals 255/17 i think u can at least go 245 with your 8" wheels. He now has Eagles or something just cheapo ones but seem to be ok.. i think it MAY have something to do with his full sick mechanical diff but not sure

I read up to this post made by Dent ... anyway he is talking about my car here. I have crappy 255/17 Federals on the rear and I dont loose any traction kicking it off the line at 4000 RPMs. I have a mechanical diff and I think this makes all the difference. Apart from this Dents car is better equipped suspension wise. I also think is has a lot to do with the way you launch the car, releasing the clutch and so on!

I put new tyres on yesterday and decided to launch them hard right away. They were absolutely appalling so I backed off. When I got home there was a layer of oily residue around the paint work of the rear wheels, evidence that "lubricants" had come off at once. It looked very similar to when I got off the skid pan!

I'd be keen to know what you think of the K104's once you've had them for a while.

I'm thinking of getting them on my 17's (235/45/17) next time around.

Cheers

J

Just got some RE540s (second hand) fitted to the rears - huge difference, the stiff sidewall, which is kevlar reinforced really tightens up the handling, and they stick - probably a bit too much for my liking, as I dont mind a bit of throttle steer.

Next I think I will be trying to source something similar to 540s for the front and giving trampios a bash for the rears.

ive got pierelli pzero's 255s on my 33 gtst with 141rwkw and it will spin if you launch at like 3000rpm, of course it will spin when u do that, but other than that it loves it. hardly ever spins. vare rare to get it to chirp as its got so much grip. my wheels are 17" not sure on other placard stuff. just 17" 255's on the rear. bloody expensive tyres too, like $500 each

ive never felt better tyres in my life. they are great, well worth the money

i'm a fan of the trampios r1r's.

i've been using them for about 6 months now with a couple of trackdays, wear is fantastic, grip (wet and dry) is fantastic. with ~200rwkw and 255's on the rear i can't spin them up - though its not like i ever do 4-5-6000rpm dumps!!!

i'd like to try the azenis's next just to compare.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...