Jump to content
SAU Community

deep_space
 Share

Recommended Posts

hello everyone. i am slowly building an rb30 for my gtst. i decided i want to get good power but be as reliable as possible too. so i am doing some hours (read lots) of work to the block.

flattening all of the casting marks on the internal walls, i am also going to redrill the oil drains and smooth the larger oil drains. here are some pictures for you

168760_1703580901742_1004571725_31872809_4416097_n.jpg

167720_1703584061821_1004571725_31872811_8172780_n.jpg

IMG_0317.jpg

IMG_0318.jpg

Link to comment
Share on other sites

I agree with you there, but I get abit anal when doing stuff like that and when some bits looked out of place or not as nice as others I just had to keep going until it was satisfactory. A little ocd sometimes....If I had more time I would have gone over it with the cartridge rolls and got it proper smooth lol.

Link to comment
Share on other sites

Can I ask what the benefits are from this?

Is it basically the prevention of the casting marks coming off and causing damage?

I want to give it a crack prepping this bottom end I have soon, (lots of research to do still).

Edited by brlucas
Link to comment
Share on other sites

Can I ask what the benefits are from this?

Is it basically the prevention of the casting marks coming off and causing damage?

I want to give it a crack prepping this bottom end I have soon, (lots of research to do still).

Yeh prevent loose casting flash from coming off and clogging the oil pickup screen. Also helps oil return as it slides down the walls back to the sump. When coarse it holds alot of oil. But it will also strengthen the block, be it an immeasurable amount by removing stress risers from the rough finish along the casting joints.

But most importantly the inside of your block looks nicer! lol.

Link to comment
Share on other sites

r33_racer what did you use? i have spent bloody hours on it and i am no way near finished. i am using a crappy electric die grinder with stones, i am trying to get the smoothest finish possible.

i am aiming for a fairly high horsepower engine with as much reliability as possible. i want to use a dry sump setup too to erradicate all oil problems. with a gt4094 turbo on top :)

Link to comment
Share on other sites

I used air die grinder with a big round burr for the open areas and then a smaller round burr for getting into the tighter areas. Also, if you are using an air die grinder get yourself a regulator if you dont already have one that lets you adjust the airline pressure. Set it low, like around 30-40 psi so you can just hold the trigger flat out and it will maintain a usable speed. Makes it alot easier on your fingers since you end up doing it for hours at a time. I got a rubber band and held the trigger down that way. You may need to play with the air pressure as all die grinders are different.

Obivously make sure the burrs you are using are for steel, not ally too.

Link to comment
Share on other sites

I did a Small block v8 with a cheap electric die grinder...took days and the shitty stones were gone after about 10 mins...worst part of not living up in QLD anymore is the lack of all my Dad's tools haha

Link to comment
Share on other sites

  • 1 year later...
  • 4 weeks later...

Years ago, when i rebuilt my old L series for my datto 1600, i read through the book on "how to maximise the potential of your L series" and one area it focused on was block prep, basically doing what has been done here, but going one step further and actually painting the internal walls of the block, so that the walls are completely glossy, allowing the oil to drain back to the sump as quickly as possible, probably more important in a race engine 20-30 years ago, running minimal baffles and a small capacity sump as opposed to todays standards, but never the less an interesting insight as to what extent builders went to.

I did it all to mine, and it really didnt take much longer to do with the right tools.

Link to comment
Share on other sites

  • 3 weeks later...
  • 2 months later...

i spent a few hours on a rb30 block i have plans for, drilled the hole for the relocated tensioner, half drilled the drains to 8mm (need a longer drill bit if anyone knows where to get one) drilled the main bearing oil galleries out to 7mm, drilled the plug out of the main oil gallery so i can clean all the swarf out & also enlarge that a lil bit. pics are showing the difference between the standard size oil gallery and modified

img1831qc.jpg

img1830ng.jpg

img1832hl.jpg

img1833n.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



×
×
  • Create New...