Jump to content
SAU Community

Recommended Posts

One of my GTS-T's came with an old worn set of keys so I took the key to a local locksmith who put the key in a machine to measure it and create the code number for it. They then cut a key to the code and gave it to me to check in the car locks.

When I confirmed that it worked perfectly they gave me a printout of the code so that I can have keys cut from the code instead of an existing key in the future - this way you get a perfect key every time.

The only problem is finding a local locksmith that has the equipment to cut a key from the code and most of the small key cutting services can only copy a key from one that you provide.

Link to comment
https://www.sau.com.au/forums/topic/378299-r32-key-code/#findComment-6033529
Share on other sites

The code is also on the drivers door lock. Know this because my key snap in the lock 2 weeks ago so I bought the lock to the locksmith and he cut a new key from the code. Cost me $25, but he charged me another $15 to take the lock apart to get the snapped key out and clean the lock. He also told me the spray CRC in all my locks because it looked like my car had been underwater. Haha. The locks are like new now.

Link to comment
https://www.sau.com.au/forums/topic/378299-r32-key-code/#findComment-6034156
Share on other sites

The code is also on the drivers door lock. Know this because my key snap in the lock 2 weeks ago so I bought the lock to the locksmith and he cut a new key from the code. Cost me $25, but he charged me another $15 to take the lock apart to get the snapped key out and clean the lock. He also told me the spray CRC in all my locks because it looked like my car had been underwater. Haha. The locks are like new now.

yeah i knew there was a lock somewhere in the car that said it, but couldn't remember. the people i bought my old business off also had a locksmith so i went there to get a key cut when i had my 33 and the keys i had were a bit worn and they said i could just get the code off one of the locks and then they could cut me a new key.

Link to comment
https://www.sau.com.au/forums/topic/378299-r32-key-code/#findComment-6034524
Share on other sites

I could open my car by putting the other half of the broken key in the door lock so all I had to do was remove the door trim, remove 1 screw holding the lock and the metal rod that unclips. This was on my R33, but should be the same on the R32. I hope your car is unlocked.

Link to comment
https://www.sau.com.au/forums/topic/378299-r32-key-code/#findComment-6036942
Share on other sites

sounds like your local nissan dealer is clueless. . . .if you give him the chassis number then he can use that to give you the key code, very useful when you dont have the original key like i did when i bought a 31 without any keys whatsover

Link to comment
https://www.sau.com.au/forums/topic/378299-r32-key-code/#findComment-6037068
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...