Jump to content
SAU Community

Recommended Posts

Dezz, Rimon just watched this video (filmed in melbourne), DAT SOUND 7:05 stock as well :O

looks like he starts/finishes at one of the shops on elizabeth st/peter stevens

onboard sounds heaps like my 2fiddy...

nice bike too expensive

Edited by R-SPEC

62% flour, palm oil (wont hurt you unless you are an orangutan), tapioca starch, salt, acidity regulators 501 and 500, thickener 401

so in reality it's flour, oil, starch, bi carb soda, mineral salt and seaweed......

actually not that bad at all

the flavour sachet's however are actually 101% msg

ingredient make-up is one thing, the process of over-deep frying in oil is another thing haha

lul what?

Find that hard to believe haha. I'll ask my boss at work who used to manage a factory which made instant noodles. Wont name any brands due to public forum :/

Basically, instant noodles are deep fried noodles cooked in a lot of oil. Most likely because they are soaked in oil from the beginning thats why they dont stick together.

/FMCGknowledgeAustralia

They stick together case they dry and hard as fuhhh. Water gets into them and they just go all soft.

your all f**king Asian lol

Nong Shim iirc the brand is the only one I liked, was spicyyyy and good

But heard that and stopped eating them, was on news or something i think i heard it

your all f**king Asian lol

Nong Shim iirc the brand is the only one I liked, was spicyyyy and good

But heard that and stopped eating them, was on news or something i think i heard it

http://www.snopes.com/food/warnings/noodles.asp

Maybe my technique on bench press wasn't the best, held arms a bit further out and felt a little easier tonight? Unless I'm getting stronger :D

If you hold your thumb out, tip of the thumb on the edge of the knurling is a pretty good position, assuming standard knurling.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...