Jump to content
SAU Community

Thread For My Car Problems.

lilcrash

By lilcrash,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 886
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

GTScotT Grand Master

GTScotT

Posted
Posted

Can you confirm a couple of things...

When you pressure test the system, u remove the afm and put in ur test fitting. That means ur intake pipe is in the pressure system, yet has non pressure areas being compressed. Ie your bov pipe and presumably the breather hoses that go from the ex rocker to the intake pipe, yes?

To rule that out please do the test on the system post turbo instead of pre, and make sure ur motor is on TDC. Then work ur way thru to see where its leaking, work forwards... So from there go to ur cooler entry, cooler exit, crossover pipe, throttle body. Work forward until u track how far the leak is into the system.

Ur breather shouldn't need ur finger put over the gromit, that means ur pressurizing ur sump... Obviously from the ex rocker breather via the intake. Otherwise ur PVC is ficked too. Test this before anything else.. Then test the guys infinite boost (blocked actuator) theory and see if it can actually make that boost up high when it cant possibly bleed it off.. If it can do it then u know the issue is boost control (actuator/wastegate arrangement).

Report back and well all help from there.

lilcrash Veteran

lilcrash

Posted
  • Author
Posted

Yes that's how I've always done it, it did blow my intake pipe off once, took 2 hours to get it all back on and ready to test again. My bov does have a tiny little leak on the outlet side between the bov and the pipe adapter, not a problem during running. I no longer have the pipe that goes to the intake pipe from the tappet cover, that's the pipe I put my finger in. You can see it in the photos.

lilcrash Veteran

lilcrash

Posted
  • Author
Posted

it will make over 20psi at 6500rpm, hard to hold it steady there without going stupidly fast. so i crept up to 6500rpm at between 15 and 20 psi then i put my foot down a bit quicker to see if it would make 25. not sure if this is a deffinative answer but makes me feel better. so new actuator and new tune and my car should be fine, hopefully the heat soak issue will be resolved with the tune. thanks everyone.

pipster11 Grand Master

pipster11

Posted
Posted

whats running to your p/s pump if your using that as a boost source?

is the p/s side blocked off?

did you use new hose for your boost to wastegate feed? one of the factory lines has restrictors in it

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

DVS can you pm me a prIce on a retune please.

Thought i did buddy, ill send u another one.

Let me know how u go with the new actuator, more preload, and put the boost source for the actuator in the cooler pipe just out of the turbo.

SargeRX8 Grand Master

SargeRX8

Posted
Posted

it will make over 20psi at 6500rpm, hard to hold it steady there without going stupidly fast. so i crept up to 6500rpm at between 15 and 20 psi then i put my foot down a bit quicker to see if it would make 25. not sure if this is a deffinative answer but makes me feel better. so new actuator and new tune and my car should be fine, hopefully the heat soak issue will be resolved with the tune. thanks everyone.

How long ago in that HG thread did I say it was the actuator lol.

This IS a definitive answer. Your car made more boost at points it never could when you eliminated the actuator from the equation. Done and done. Get that new bitch on her and enjoy.

lilcrash Veteran

lilcrash

Posted
  • Author
Posted

Sarge. I did believe you but I didn't have a safe way to test it, that's where my wife comes in handy.

There isn't any boost feed going to the ps pump, I used new vacuum line to the turbo.

Yer I deleted it by accident and couldn't remember what you said.

lilcrash Veteran

lilcrash

Posted
  • Author
Posted (edited)

That's the vacuum valve on a neo rb25. That's what I took the line off, il trace the other line and see if it's causing a leak.

Edited by lilcrash
MBS206 Grand Master

MBS206

Posted
Posted

I thought the Hypergear turbos had a nipple on the outlet of the turbo already for that purpose...

If not, do as Jez has said and put a brand new nipple on the intercooler pipe, nice and close to the turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...