Jump to content
SAU Community

Recommended Posts

hey does anyone know where i can find another fitting for the RB25 NEO water outlet to radiator (on the intake manifold) it has corroded and im struggling to find a new one.

i found a picture of what im talking about (this guy is holding a new one)

rb25detintake-1.jpg

  • 3 months later...

You can take the manifold off and get a pipe welded in place (any ally fabricator)and a bead welded on the end to stop the hoses blowing off, i did this with my 20DET to get rid of the adaptor that steps the hose to a smaller diameter, didnt cost much and it works fine

  • 4 weeks later...

That part looks like it is supposed to corrode - that is - be the "sacrificial anode" in the electric circuit created by the coolant. In older cars i've worked on the thermostat housing typically performed this function. If you want to understand why, google galvanic corrosion.

tl:dr - only use the replacement Nissan part so that the head and/or block dont start corroding.

http://www.300zx.com...ylineengine.htm

UAS Chrome Molly Upper Radiator Outlet Intake Manifold

Replaces often rusty factory one.

PRICE: $65

This is what mine looked like

019dcw.jpg

Holy crap! It looks like tap water has been used in that cooling system.

  • 1 year later...
  • 3 months later...
  • 1 year later...

Mine is corroded but not so bad I have to replace it just yet, but when I looked I was going to cut it way using a dremel and a tungsten bit. So slot it and then collapse it. Not sure if thats the best method but reckoned it could work. Be careful not to hit the alloy though, don't really want to scuff it too much.

Pretty sure you could then mike it up and get an exhaust place to make up a new one, if you only have to do it every 15-20 years trhen I don't see a big problem.

I had that issue about 2 years ago, I thought I posted here but I'll chime in Now

I took it to a mechanic and he said he'd seen it heaps, he said he would use a chisel and then collapse it like the other person above has said, then he had an exhaust place make a piece and roll a lip in it

I didn't want to have half a go and do something wrong and then have to tow it So let him do it for me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...