Jump to content
SAU Community

Recommended Posts

want to make up a heatsheild, just wondering what the best material is?

Has anyone used the heat sheild that supershit autos sells? It looks good, but would it just be the same as using some alloy plating?

Just going to copy the design of the stock sheild unless there are better ideas out there.

Link to comment
https://www.sau.com.au/forums/topic/387307-best-material-for-turbo-heat-sheild/
Share on other sites

Mate best way to make a heat shield I've found . and looks absoloutely mint

Although ur missus might not thinks so

Roughly measure your turbine housing

Take a walk into your kitchen grab out ur stainless Steel saucepans

Find the one closest to the size u need try and not let the Misso see u hahahahah

Take it to ur shed an and cut it in half

( obviously using the side that doesn't have the handle on it ;-) )

Mark ur bolt holes drill to suit

And ur away :-)

hahaha that is f**king awesome, how well does the kitchen pot work?

Does it have to be stainless steel or do the "non-stick" teflon ones work too?

Might try find a clothes dryer too then.

Ideas like those two are great

acl heat sheild is what you want, your local repco can order it in

http://www.aclperformance.com.au/prod_heatshield.htm

that's the stuff i saw at supercheap, so it actually works and isn't just a cheap supershit item? Well at $50 a sheet i wouldn't call it cheap.

It looks pretty pro anyway, have you used it and is it effective?

The wonky shape was intentional, the far left was taken out further to block any heat excaping out the gap and to give protection to the ABS wiring.

And its better than the beanie which cost $250 and didnt last.

middle pic is what is left of the beanie..

I have also used the ACL heatshield which took me about an hour to do.. I found an old pic of when i first finished it, has since been refined and dodgey piping removed :P

post-51757-0-03069300-1326015813_thumb.jpg

middle pic is what is left of the beanie..

I have also used the ACL heatshield which took me about an hour to do.. I found an old pic of when i first finished it, has since been refined and dodgey piping removed :P

What inlet manifold is that David not a common Type we see ,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...