Jump to content
SAU Community

Recommended Posts

There is a thing called:

Brake specific fuel consumption (BSFC)

It's a figure to describe how much fuel an engine needs to produce X amounts of power.

http://www.land-and-sea.com/dyno-tech-talk/using_bsfc.htm

There is a calculator on this page ->

http://www.rceng.com/technical.aspx

My (standard) injectors are now at 85% duty cycle, I am making about 330HP at the crank. (running at AFR of 11.7)

The mixture was starting to lean out already, so I have ordered new injectors.

Edited by Torques
  • 2 weeks later...

From my personal experience the standard injectors can hold more than most think. As my 33 gtst is making 393hp@wheels on standard injectors...

For the dyno figure doubters it does 119mph down quarter..

Edited by fragz013

My (standard) injectors are now at 85% duty cycle, I am making about 330HP at the crank. (running at AFR of 11.7) The mixture was starting to lean out already, so I have ordered new injectors.

Hmmm if you are finding that the fuel flow into the engine is levelling off at 85% IDC I'd consider looking at whats supplying fuel to the injectors more than the injectors themselves, personally - what pump is that with?

almost 300 rwkw? doubtful

119mph isn't a bad trap speed though, to be fair... though in saying that when you are limited by small injectors you can still make a car quite a bit faster than many would expect doing sneaky wee tricks. At lower rpm you have a longer pulse period, so you can actually move more fuel with an equivalent duty cycle.

As an example - I've tuned a Silvia running a G4 Link & boost control but still on stock injectors was quite held back, hitting 85% at 7000rpm at the boost level we were setting it up for. That boost level just wasn't going to do the setup justice, so I set up a "tapering" boost curve which resulted in a boost level some 6-7psi higher at 4500rpm than at redline and progessively dropping down... but injector duty cycles still never went over 85%. The resulting change in how the car performs is VERY substantial, torque wins races and hp sells cars?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.  
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...