Jump to content
SAU Community

Recommended Posts

hey guys,

took my car to get fuel in the morning yesterday, then washed it. ready for heathcote drag day. we left for the hume highway at 7.30, the car got to the servo fine where we met up with the rest of the cars attending. when we left i started the car all was ok, was travelling down the highway at 100Kmph, then all of a sudden felt the car not shaking but more like a shutter sort of like when you are about to stall it in a manual but all the time...when i accelerated the car would go nowhere untill the turbo kicked in then it JUST dragged the car along...we stopped at a safway on the side of the road, and i turned the car off and back on, and it still done it...i looked under the bonnet and everything seemed ok....i als checked for boost leaks using my gauge, and vaccum and boost was fine...i then turned the car off, left it for a bout 5 mins and turned it back on and it was FINE??!! i still didnt trust it so i left it there all day and went to the drags without it. i came back later that afternoon to grab it and it started fine, drive 50 mins home fine and now runs fine...i cant fault it now??

the car also sort of missfires when i put the foot to the floor at 5000 rpm, but the revvs still keep climbing like normal??? i changed the coilpacks and that helped a LOT, but it still does it under full throttle...its not like a missfire but like a stutter??

can anyone help with BOTH these problems???

cheers!

Link to comment
https://www.sau.com.au/forums/topic/391524-car-playing-funny-buggers/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Id point towards a plug or sensor got wet or the fuel you got had some crap in it. seen as the only 2 things you did was wash it and put fuel in it. it might clear itself up after a drive, don't flog it to much in the mean time

In the boot, remove the back board, you will see 4 10mm screws holding down a plate. Remove that. Under there is a black lid thing with 3 hoses. You want to unplug the wires and get a rag ready for when you remove those lines as fuel is going to come out. Keep the hoses out of the way and take that lid off. To do that get a piece of wood and put it in the notches in the lid and tap it with a hammer to loosen it and get it out. Fuel pump is inside. Plenty of guides here to elaborate and show pictures of how to do it, wire it and fit it back in.

Its not a fun job. Don't do it on a hot day and be ready for swearing. DO NOT EVER attempt to do it with more than a quarter fuel in the tank. Hell run it to near empty if you can.

Fuel pump isn't that hard if you get a good one. my tomei pump was easy as. pull the old one out, drop the new one in

This. Took me half an hour, including diagnosis of why the car wouldn't start when I reversed the polarities :P

Agree with running the tank near empty first though. Arms get real damn itchy immersed in petrol ermm.gif

Edited by Hanaldo

This. Took me half an hour, including diagnosis of why the car wouldn't start when I reversed the polarities :P

Agree with running the tank near empty first though. Arms get real damn itchy immersed in petrol ermm.gif

And in a hot day, that itch plus the humidity rising from the fuel tank is enough to really f**king frustrate you when you cant get that cradle in the bracket.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...