Jump to content
SAU Community

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Not sure if anyone is interested;

I have a pair of Cad plated steel R32 GTS-t caliper offset brackets to suit 350Z rotors; High tensile bolts and all mounting hardware.

I bought them to do an upgrade on my Stagea; but ended up going R34 GT-t 310mm; so I don't need these.

Paid $100 from the US, but I was hoping to get around $60 (plus postage) they are unused; only trial fitted to a caliper to check clearances.

Feel free to PM if you'd like some pics.

  • 2 months later...

GK tech now make these adapters BTW:

http://www.gktech.co...sp?id=GTRX-ADPT

Good value, shame there is no option for 34GTT though to go to bigger rotors :(

I downloaded a free cad program and had a couple of mild steel brackets laser cut for my car, std caliper 310 to 324.

This lets me run some local 2 piece gtr rotors for track days - x3e brand.

These are heavy brackets with only a 7mm radial increase, but alloy hats should reduce the weight and be better at dissipating heat.

I haven't fitted them yet, as need to sort out how to secure the hard brake line.

A better option would be to use 330x32 rotors, but this needs too much modification to the sumitomo caliper, ie. a 2mm packing spacer, longer caliper bolts, longer retainer clip pins + sourcing longer internal brake fluid gallery o-rings.

Will post pics when sorted.

GK tech now make these adapters BTW:

http://www.gktech.co...sp?id=GTRX-ADPT

No they don't. Those are to suit R32, Z32 and S13/14/15. R33 is different as the calliper legs are to suit a 296mm, not 280mm.

I downloaded a free cad program and had a couple of mild steel brackets laser cut for my car, std caliper 310 to 324.

This lets me run some local 2 piece gtr rotors for track days - x3e brand.

These are heavy brackets with only a 7mm radial increase, but alloy hats should reduce the weight and be better at dissipating heat.

I haven't fitted them yet, as need to sort out how to secure the hard brake line.

A better option would be to use 330x32 rotors, but this needs too much modification to the sumitomo caliper, ie. a 2mm packing spacer, longer caliper bolts, longer retainer clip pins + sourcing longer internal brake fluid gallery o-rings.

Will post pics when sorted.

Nice one! Will wait for pics and results :thumbsup:

  • 4 weeks later...

I am finally going down this path..... Using 350mm Evo rotors with Evo callipers, are there any downsides to doing a brake kit with adapters? I assume an engineer can check and pass them for road use? (They state offroad use only but i guess an engineer may be able to pass them if they meet requirements?)

I am a brake noob so any advice would be good :D

I've just bought a set of rda slotted gtr rotors to try with my caliper adapters, just waiting for my dba 4000s to wear down before I upgrade.

Now, after using the standard gtt brakes on a racetrack winton/sandown, they hold up pretty well with the right pads and ducting - I still need more air though as rims are very hot.

Maybe you should give this a go then go bigger if not happy - if your tracking.

  • 1 month later...

Sorry guys, we have had a million things going on and are literally working 80-100 hour weeks.

Just this week the design of our rear knuckles was signed off (350 hours or so in the design) and we're now working on R32/R33 knuckles. In doing that, we've got an R33 knuckle (aka upright) sitting here and I'll get it measured up in the coming days.

There is a VERY good chance that the brackets will be $99/pair with fasteners. We'll machine them out of 7075-T5 for some extra strength and unlike the UAS brackets we also run thread inserts.

A few install pictures of our S14/S15/R32 brackets can be seen here: http://www.skylinesa...ost__p__6549940

To keep up to date, check out our facebook page here as we'll post up about an intro price there (probably $79/pair): http://www.facebook.com/gktech

Greg

Apart from Unique Autosports does anybody else make the brake caliper adapters to go from 296mm to 324mm rotors?

These are to use the stock GTST calipers with the larger GTR rotors (going to use the 2-piece ATTKD rotors I think).

If not I guess I'll just have to fork out the $350 for the adapters.

ADAPTERS

didnt read the whole thread but holford motors make a kit with the mounts and rotors for $330

http://www.ebay.com.au/itm/HFM-GTR-324MM-Rotor-Upgrade-Kit-With-Caliper-Adapters-/150879077844?pt=AU_Car_Parts_Accessories&hash=item23211805d4

Edited by Frosty

didnt read the whole thread but holford motors make a kit with the mounts and rotors for $330

http://www.ebay.com....=item23211805d4

No. These are effectively the same as all the others out there. They suit changing from 280mm rotors to 324mm. They do not suit upgrading R33 296mm rotor/caliper setups to 324mm rotors.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...