Jump to content
SAU Community

Recommended Posts

I have the OEM mat, it isn't that great as all the crap slides around in the back now. Im sure there is a better material to make it out of, even plain rubber would work better as Josh said.

Great for taking the dog for a drive though.

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6261341
Share on other sites

There's a sweet mat that actually goes up the back of the rear seats and the headrests go through it. So when you fold the seats down and presumably put a bike/snowboard/etc in there, it's covering the whole lot instead of just the "cargo area".

But yeah, only ever seen one on YAJ and it was stuffed.

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6261344
Share on other sites

Luckily I have both of the factory mats, the rubber mat and the mat that runs up to the back of the seats for when you fold them flat.

About 2 months ago I did see a set of mats that covered the wheels arches that matches my mat but I forgot to bid on them. Never seen either of the mats before or after that on yahoo.

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6261362
Share on other sites

Wouldn't be too hard to get a trimmer to make one up, surely. Just got to find one that works for cartons.

Best bet would be for someone that has one to take it to a trimmer and get them to replicate it.

Is that the sound of a group buy starting up Jase?

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6262631
Share on other sites

I guess it would really depend on what everyone wants.

I'm pretty happy without one, but if I was going to get something it would be some sort of carpet that went up the back of the seats like we were talking about above, but with a washable, water resistant carpet. That way after a muddy day on the bikes it can be pulled out, hosed off and chucked on the line to dry.

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6262644
Share on other sites

So you would want it out of a marine type carpet? The factory one isnt carpet, it's a thin fabric with a thin rubber back.

I'll see what they can offer.

That's what I used. Just cut the right width and then make the cuts so that it sit nicely with the seats down (and covers the headrests too - my dog put his claw through the leather on one of them).

Cheap, easy and works very well.

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6263046
Share on other sites

So you would want it out of a marine type carpet? The factory one isnt carpet, it's a thin fabric with a thin rubber back.

I'll see what they can offer.

I suppose. The fabric with rubber back would be just as suitable I guess. I'm not really that serious about getting one to be honest..

Link to comment
https://www.sau.com.au/forums/topic/393710-m35-cargo-mat/#findComment-6263055
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...