Jump to content
SAU Community

Recommended Posts

Yehh, results would be excellent :glare:

Haha would use E85 if it was an option here, but I'm not paying $3 a litre. Until it becomes more available, I'll be on PULP.

It'll happen man!! No rush ;)

Hope you get the E85 over there one day soon!

Haha yeh, would be good. At the moment I'm more likely to go WMI, it's just way easier. To be honest though, I think any more engine mods are on hold for awhile. Whatever power it makes with this tune is where it will stay for now. I just want to drive the damn thing again. The original plan was to have it ready for the reopening of Barbegallo, but I've overshot that by about 2 months now :( Dying to hit the track again.

Actually next money might be on a lap-timer, I still don't know what I'm getting around Barbs :unsure:

So the saga continues... Engine failed on the dyno today. Valves are sticking open. Don't even know where to start, but tomorrow I have to pick the car up and get it home. No idea where it goes from here.

So the saga continues... Engine failed on the dyno today. Valves are sticking open. Don't even know where to start, but tomorrow I have to pick the car up and get it home. No idea where it goes from here.

Boo

Timing belt?

Unfortunately RBs are interference motors :(

So sad to hear this man!

Nothing so obvious. If it had been a complete engine failure then I could just buy a new motor. But according to Sean, mine is still drive able. It's only when he tried to do a full load power run that the engine loses compression and he has to abort.

Nothing so obvious. If it had been a complete engine failure then I could just buy a new motor. But according to Sean, mine is still drive able. It's only when he tried to do a full load power run that the engine loses compression and he has to abort.

This has been burning my brain man! It doesnt add up....

  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...