Jump to content
SAU Community

S A U N S W - Texi, "the Original" @ Sutton Road

N1GTR

By N1GTR,
in Events Archive

 Share

Recommended Posts

  • Replies 219
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

luke gtr Grand Master

luke gtr

Posted
Posted

Semi slicks, check.

Full tank if fuel, check.

Raised suspension to not foul tyres, check.

Boost controller, tomorrow.

Nearly all systems go for sutton.....

Woooooooooooo hooooooooo

Jimmy_8472 Proficient

Jimmy_8472

Posted
Posted

Yes spaces left. Send the form and money today and you'll be fine.

There is no extra cost for the CAMS license other than the actual cost of the license (eg it costs you no more to do it on the day, but the license cost still has to be paid)

So it turns out i can't afford it at the moment, which sucks epic....

hopefully you guys get a good turn out and we'll be able to do another one in the not too distant future.

I might still come out to spectate a little bit though, maybe.

BunsenBurna Proficient

BunsenBurna

Posted
Posted

Scott, don't worry so much! You'll live longer :D

There is a slow lap at the start where everyone goes in single file at a slow pace so you will be familiar with the track.

By mega power, I'm talking 420rwkw and upwards. I'd expect you to be in 2nd or 3rd for the whole run (of course with the exception of 1st at 7500rpm for the launch at the start)

Also that crest is like any crest you see in hilly parts of Sydney, for example the big one in Greenwich. You're not encouraged to go flat out over it and by doing so your time will be slower anyway so stuff that. If it's really bothering you I'll take you to it in the morning before runs start and drive over it myself with you in the car to demonstrate it's perfectly harmless when common sense is used :)

What are you talking about Steveo?!?!

I'm worried that I (a) WON'T get air and (b) won't get in to fourth gear.

If I don't get into at least 3rd gear with my 310awkw I'm going to be devastated. And I will only be launching at 1250 rpm in first.

I'm very familiar with that crest in Greenwich in fact I know someone who got monster air off it, crashed and now has monster metal plates in him. Retard.

Car is still being tweaked as I type this so it can't get much more prepared than that (assuming I get it back in time). Bring it on!

Hipcrostino Rookie

Hipcrostino

Posted
Posted

So lets say I want to enter. I can fill out the form and fax is etc, but what about payment?? Even if I transfer it first thing tomorrow chances are it won't appear in your account by the end of the day. Cash on the day ok???

Shell Grand Master

Shell

Posted
Posted

So lets say I want to enter. I can fill out the form and fax is etc, but what about payment?? Even if I transfer it first thing tomorrow chances are it won't appear in your account by the end of the day. Cash on the day ok???

Yes bring cash on the day... make sure it is the correct amount, we don't have oodles of change!

Duncan Grand Master

Duncan

Posted
Posted

Brakes bled see u ladies there

What's with the early night bludger?

I've just knocked off, wrecker motor in the car, seems to be running OK. Thanks to Mark and the boys at Hills Motorsport for putting on some late nights to help get it ready.

See y'all on saturday

hamiltonau Grand Master

hamiltonau

Posted
Posted

kept half asking Steve tonight if we ended up with the numbers to do another one of these things, sure hope so.

He would then burst out in laughter at some ribald joke someone or another had made and im pretty sure half of Canberra had to hear us giggling away as we drank the only pub for miles dry of all its finest lager.

Good times folks.

and i havent even turned a wheel in anger yet..

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...