Jump to content
SAU Community

Power Steering Fluid Leaking Consistently

R0yalT
 Share

Recommended Posts

R0yalT Explorer

R0yalT

Posted
Posted

Hey SAU,

I just bought my first GTR (and Nissan car for that matter) 2 months ago. During the first 2 weeks in my possession, there were no leaks.

One night when I was backing the car out, I saw a small puddle. I came back home shortly after and put a tray underneath (left side/turbo side).

Next morning I inspected the tray and found out it was red, could only be power steering fluid (Dexron ATF). I researched around and concluded the leak can either be Power steering itself or from the Attesa unit.

I searched around GTROC and SAU and someone recommended Nulon Power Steering Stop Leak and Conditioner, it worked for them so why can't it work for me?

It doesn't work unfortunately, it still leaks (a drop every hour or two I reckon) and now screeches on full lock (power steering doesn't like the fluid).

I have recently lifted the car and took off the front diffusers to take pictures.

Any help to solve this problem would be greatly appreciated! (From a R34 GTR, I don't think it makes a big difference but just incase people are asking).

photo_2.jpg

Really wet

photo_1.jpg

This is where the drips are coming from I guess.

photo_4.jpg

This thing was wet, I thought this was the culprit at first. This should be ok right?

photo.jpg

Slight oil dripping from corner of sump (I can't remember but I'm sure it was the sump), should be ok right?

Yet again, any help would be greatly appreciated. I need this fixed so it doesn't play in the back of my mind when I start building this monster.

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Dose Pipe Sutututu
Dose Pipe Sutututu

Replace reservoir lines, they weep and usually are the source. I replaced mine with aftermarket gates oil hoses. 3/8" and 5/8", if money permits go OEM - I went aftermarket because I ended up fittin

GTSBoy
GTSBoy

There's no seal on an R34 cap, and as it just clips on, I wouldn't think that you could get it to stay put if you snuck even a 1mm piece of soft neoprene foam under there.

Posted Images

MrStabby Grand Master

MrStabby

Posted
Posted

On my BNR32 that hose started to leak, so i removed it and had Enzed make up a new rubber section and fit it to the metal tube section. Was a bitch to remove.... FWIW im using Transmax Z (synthetic) fluid without issue.

MrStabby Grand Master

MrStabby

Posted
Posted

I cant remember, wasnt expensive at all. It would be cheaper than getting the part from Nissan, and you wont have to wait for it to come from Japan. On my hose I could see the blister in it, i guess you cant be as sure that hose is the problem because of that loose cover hose over the top.

  • 2 years later...
V28VX37 Veteran

V28VX37

Posted
Posted

Digging up an old thread, I've got a similar problem. My power steering reservoir looks like it's always been weeping a bit but now I have drops coming down on the left hand side under the engine bay. See below for a pic.

Any suggestions on how to investigate and remedy this? Is it just the connectors/lines or is my rack going too? Could it be leaking from multiple spots?

Also, can you recommend a PS specialist in Melb who knows Skylines...?

14006154874_590ee9d284_z.jpg

Thanks!

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Replace reservoir lines, they weep and usually are the source.

I replaced mine with aftermarket gates oil hoses. 3/8" and 5/8", if money permits go OEM - I went aftermarket because I ended up fitting a power steering cooler when I did my lines (no more boiling on the track)

  • Like 1
89CAL Grand Master

89CAL

Posted
Posted
Replace reservoir lines, they weep and usually are the source.

I replaced mine with aftermarket gates oil hoses. 3/8" and 5/8", if money permits go OEM - I went aftermarket because I ended up fitting a power steering cooler when I did my lines (no more boiling on the track)

Off topic here but what did you notice when the p/s fluid boiled? Im still troubleshooting a problem with mine, and because the reservoir sits so close to the 6 boost manifold im wondering if its to do with heat. I lose nearly all the assistance from the power steering tge 2nd or third time I start the car (so when its been hot and then started) im womdering if my pump isnt 100% and when it gets too hot the pump isnt working efficently

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Off topic here but what did you notice when the p/s fluid boiled? Im still troubleshooting a problem with mine, and because the reservoir sits so close to the 6 boost manifold im wondering if its to do with heat. I lose nearly all the assistance from the power steering tge 2nd or third time I start the car (so when its been hot and then started) im womdering if my pump isnt 100% and when it gets too hot the pump isnt working efficently

Oil all over the reservoir dribble down the lines and loss of fluid - only happens on the track.

I don't lose all assistance or that, just half the oil dribbles out and makes a mess in the engine bay.

Since I've installed my power steering oil cooler (used R33 AT cooler) no more, no dribble shit, no dirty reservoir and my lines looks fresh :)

89CAL Grand Master

89CAL

Posted
Posted

Yeah im getting voltage to the solenoid when the problem occurs. So not sure if the PWM is right but I believe it is. I want to change the solenoid but cant source a new one because they dont make them anymore.

I never had issues before I changed the engine. And we accidentally ran the car on initial start up with no power steering oil so was suprised the pump has been so good lol

I have a spare. I think ill just change it out and check the wiring to the solenoid

SiR_RB Grand Master

SiR_RB

Posted
Posted

I've got a power steering leak aswell recently but it's coming from the drivers side near front drive shafts that a lot of lines and banjo bolts around where it leaks from

Gotta get under and try nip all the bolts up and see how it goes...

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

Yeah im getting voltage to the solenoid when the problem occurs. So not sure if the PWM is right but I believe it is. I want to change the solenoid but cant source a new one because they dont make them anymore.

I never had issues before I changed the engine. And we accidentally ran the car on initial start up with no power steering oil so was suprised the pump has been so good lol

I have a spare. I think ill just change it out and check the wiring to the solenoid

Is the Power steering really PWM? In my R32 i haven't have power steering since i did and engine swap, and i have been told that it was because i didnt give power to the solenoid inside the steering rack. I have the engine out again and i gave it 12V and i can hear it opening, so i thought it must be working fine. My plan was to just give it 12V when the car starts up but you are suggesting that its PWM?

89CAL Grand Master

89CAL

Posted
Posted

It will be fully open with 12V at it so the power steering will work fine. However (from the information ive found) the HICAS Ecu varies the PWM to the solenoid as speed increases till the assistance is no longer needed. I could be wrong but it makes sense

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

Okay, yes that makes a lot more sense. I didn't even think about that, seems pretty obvious now you have pointed it out haha. I was running a power steering cooler in my car also (R33 auto trans cooler) and i could never get the system fully bled properly. Does the cooler have to sit lower than the feed point from the reservoir? And it seemed to be worse when i had it mounted upside down (so the p/s fluid had to flow up into the cooler), i wouldnt have thought it would make that much of a difference being that the system would be pressurized when turning the steering wheel, which is the only time the system is operating.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Did you hook it up on the rack return line?

I don't have any issues with bleeding it as such.

However mines mounted a little unconventionally because of my front bar and bumper support

post-22311-13989360642774_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
    • Duncan
      R33 GTR running -9 with no tune

      By Duncan · Posted

      Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Duncan
      Coolant leak?

      By Duncan · Posted

      Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
×
×
  • Create New...