Jump to content
SAU Community

Recommended Posts

  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Mid-arvo went pass Dodgy Dave while he was looking for a park near the Parade, Norwood. I was in a black Starlet & gave a shout out to grab ya attention but, didn't hear.

What rhymes with Dodgy.. Bodgy.. :rofl:

I think Antony/Forza/Mt. Franklin should get the set of plates Bodgy 01. :wave:

spotted a fair few in the last week.............DC i dont remember seein ya last week at flinders (woulda been a monday or a wednesday as thats when im out there) but i do remember seein ya car at boostworx.......sorta thought the other musta been ya bro's car with the matching "mismatch" rim combo :wave:

spotted vange's car there (or as my mate said when we walked in "ah, theres "FLANGE"), plus a tidy silver 33 that got picked up by a young lad.

ive waved to a few 33s and 32s over the weekend, most of the 33s hav been white with white wheels *drools*

Followed a black Stagea (GRIM_R32??) this arvo. Sounds nice, has a great exhaust note :w00t:

Yeah that was me, wasnt sure if you would recognise me in the black stagea instead of the white one! lol! Got it back the other day, having to run it in is sucking big time, but will be worth it in the long run!

Yeah that was me, wasnt sure if you would recognise me in the black stagea instead of the white one! lol! Got it back the other day, having to run it in is sucking big time, but will be worth it in the long run!

ill run it in for ya :glare::laugh:

spotted a nice silver 34 today with tha bling rims @ clovercrest @ 4:00pm and 2 mins after a wine red 33 that looked nice too

/edit

woohoo quote works again

Edited by Madaz
spotted a heap of R32's tonight in town.

seen a black R32(?(couldn't tell)) in an alley thing just off

Frome St, had the plates HAUNTS

That's my old skyline, its an r33...you would have spotted the new owner because i sold it a couple of weeks ago...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...