Jump to content
SAU Community

Recommended Posts

  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hmm im not sure what plates that maccas gtr has, maybe it has something like sir 33 also! who do these guys think they are being knighted and stuff.

The sir33 that cheeky saw was at the last autosalon aswell with his springs removed for the "dumped" looked, its ok cheeky you can tell the difference hehe

  • 4 weeks later...
I know i want to take my car out Friday night as well...  

Im defected but have permit to drive it, so I figured i might as well make the most of it.  Its like an immunity sticker.

My advice, don't do it!

Read the notice carefully, you can only travel to and from place of repair.

If you are caught driving, particularly at night, you will get more headaches you don't need.

Let's not even enter in to the fact that silly canary shouldn't even be there....

Well....

If you make an appointment with Regency, you take the defect notice to the cop shop and they grant you permission to drive your car until your regency appointment as long as you show them proof of repairs.

In my case, there was no repairs required, because they defected me for something that was legal and already in place (blow off valve to be conveyed to manifold), so they granted me permission to drive. Does that make sense.

However, i have my police conciliation conference next week about the complaint i made regarding my defect. I spoke with the Senior Traffic Manager (he is dealing with the complaint) at holden hill about how the officers treated me and he agrees his officers were wrong and that my defect should be removed. So, i'll let you know what happens.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...