Jump to content
SAU Community

Recommended Posts

Hi all, im in the process of building an R32 drifter i want around 400-450hp, its currently got RB25 i put in.

MODS

Microtech LT12s

FMIC

3inch exhaust

YellowJacket coil packs

Stock everything else

its making 200kw on 12psi

My plan is the folowing mods

hypergear xIU stock 25 turbo highflow

WMI

Will this come close to that power figure or will i be better off buying a GTX 30/76?

Edited by 51NNA
Link to comment
https://www.sau.com.au/forums/topic/397558-400-450hp-rb25-build-questions/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Well you will need bigger injectors, Fuel pump, a little highflow wont make 450hp at the wheels

GTX3076 will be over kill, better off with a GT3076 or if you really want a silly billet wheel then a GTX3071 would be better suited

Assuming you mean 400-450HP at the engine, then yeah, the Hypergear highflow will get you up into that space. But you're likely to need more fuel. I wouldn't rely on the meth in the WMI to provide enough. You're also likely to need to make sure the ignition system will cope.

It does have yellowjacket coil packs, i was hopeing for RWHP and Zebra i wasnt 100% sure on spending the extra 500$ for a billet wheel, but would you go a 71 over a 76? and my injectors are only on 50%duty cycle so hopefully they would cope too atleast 370-400hp with the WMI

Are they standard injectors? If so they will not do 400rwhp, about 300rwhp is the limit at standard rail pressures

WMI should not be used to increase fueling capacity, doesnt work like that

GTX3076 is capable of 500+rwhp on the right fuel nad engine, but slightly laggier than the regular GT3076 which will do just shy of 500rwhp on the right fuel/engine

Well i was hoping too be sneaky and run my AFR at 13 with the wmi protecting against ping, ATM its 199.6rwkw with 53% duty cycle with stock injectors on 12:1 afr

Edited by 51NNA

Its pretty interesting to find that Toshi managed 2x 260rwkws R33 using our stock 21U R33 high flowed turbos on factory injectors pump 98 done on two different dynos. Not sure whats the go there, unless he can flash the stock ECU to run stock injectors at 100% injection or some thing similar.

only with toshi's remaps.

2 results out of hundreds of others doesnt make it a trend imo

Only with toshi's remaps. I remember he stated some where that he can make it do that no worries. I've never seen that done with other tuners.

Well looks like im up for some injectors too lol, 550cc be enough?

OR buy a GT30/76 or GT30/71, WMI and put it back on the dyno and see what happens and go from there, after all spending 1k on injectors i might not need (probly will do) but would be interesting too see what happens?

Edited by 51NNA

most would say 75% injector duty would be the max they would want for safety...

get siemens injectors and a new rail and it will be cheaper than sard or nismo injectors and you can get larger to support E85 and not worry about WMI....

Its pretty interesting to find that Toshi managed 2x 260rwkws R33 using our stock 21U R33 high flowed turbos on factory injectors pump 98 done on two different dynos. Not sure whats the go there, unless he can flash the stock ECU to run stock injectors at 100% injection or some thing similar.

I made 260kw at 15psi so never 100% injector duty.

Injector duty is around 88-92%.(depends on AFR)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...