Jump to content
SAU Community

Recommended Posts

Haha if u wana be dickhead...u have a way of writing emails which cracks me up.

Those pretty stickers are good for your toolbox.

U running tomei exhaust manifolds right?

:D.

Nah mate. HKS ported me a set.

I learnt the hard way with stainless junk!

:D.

Nah mate. HKS ported me a set.

I learnt the hard way with stainless junk!

now I remember when the tomei items cracked on u. Do u mind sharing a pic of these hks manifolds, when u get the chance?

this thing is going to be off its head!!!!

Yes, I believe it will, I'm thinking when it starts up Satan will be wanting to sponsor it and any red blooded male with get a warm feeling in their pants.

Yes, I believe it will, I'm thinking when it starts up Satan will be wanting to sponsor it and any red blooded male with get a warm feeling in their pants.

I'm more partial to a startup engine sound that induces a feeling of fear... Oh crap what have I built ! Instead of one that provokes a bunch of guys to get a semi...

Fear is where its at!

So no VCAM just yet... Are you still planning on using the Mines 10mm lift cams you were talking about at the nats?

I'm more partial to a startup engine sound that induces a feeling of fear... Oh crap what have I built ! Instead of one that provokes a bunch of guys to get a semi...

Fear is where its at!

So no VCAM just yet... Are you still planning on using the Mines 10mm lift cams you were talking about at the nats?

Ian. No Vcam yet but I put the Exhaust cam in that HKS and the guy that built the head recommended IF i decide to go that way later on. Actually even without Vcam Hiroyuki recommended the 264's anyway. I will be getting his 'recomended' cam settings and go from there. I'm hoping the idle will be nice and smooth, not a grumpy prick like it was with the 270's.

I'm more partial to a startup engine sound that induces a feeling of fear... Oh crap what have I built ! Instead of one that provokes a bunch of guys to get a semi...

Fear is where its at!

So no VCAM just yet... Are you still planning on using the Mines 10mm lift cams you were talking about at the nats?

But fear gives me a semi

Next time your scared... don't come near me :P

Dont be near Wakie on the 19 of May then, the fear levels may drop after the first session if the engine bay isnt covered in oil.

Im loving the power of the boat ATM but the oil issues are breaking my balls, hopefully will be fixed after the new cam covers/baffles and catch can are in.

Either that or Im just going to go and buy some Drag Radials for the rear and only go in a straight line, the car has no problems doing that, stupid f**king car.

Dont be near Wakie on the 19 of May then, the fear levels may drop after the first session if the engine bay isnt covered in oil.

Im loving the power of the boat ATM but the oil issues are breaking my balls, hopefully will be fixed after the new cam covers/baffles and catch can are in.

Either that or Im just going to go and buy some Drag Radials for the rear and only go in a straight line, the car has no problems doing that, stupid f**king car.

Well hopefullt this does it. You can't have any more black lines in your bay. It will look like a spiders web.

Have you got your latest graph handy? Throw it up if you could be bothered!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...