Jump to content
SAU Community

Recommended Posts

I used that shell oil you get in the red container...the one you see at servo's all the time - for my run in. ~$40bucks for 10L, you can't really go wrong.

Diesel oil would be fine, but the extra detergents wouldn't really be doing anything as the engine should already be sqeaky clean!!!!

Keen to see the results for this (re)build!

Edited by wedge_r34gtr

Few things to do my ass.

Lol. I was at unigroup and saw what you brought there!!!!

PS: your front cam cover looks great!! :D

Haha. a lot of the things on the list is small stuff. I had to list them otherwise Tyson would forget!!

Yeah it turned out well. Very happy with it :D

Where is yours upto?

Penrite HPR30. It's loaded with the most zinc of any oil on the market, making it perfect for run-in of camshafts/bottom end etc.

That's what I've just put in mine!

Penrite HPR30

zinc - 0.11%

I just put this in ....Why wouldn't you use this ?

Penrite Running In Oil 15/40

zinc - 0.161%

Haha. a lot of the things on the list is small stuff. I had to list them otherwise Tyson would forget!!

Yeah it turned out well. Very happy with it :D

Where is yours upto?

I was pulling front diffs apart today... Bottom end is also ready for assembly.

Penrite HPR30

zinc - 0.11%

I just put this in ....Why wouldn't you use this ?

Penrite Running In Oil 15/40

zinc - 0.161%

I think that is what I ran, pen rite run in oil. Your engine builder should guide you on what oil to use for run in

Look at a radiator filter while your getting it ready, after my rebuild it caught a fair bit or sealants and other crap, even after the chemical clean it still collects bits of crud that would have other wise gone through the water pump and maybe got stuck in the radiator.

TEFBA Radiator / Cooling system Filters

Like dis > http://www.ebay.com....=item20bddab6b4

Disclaimer: The RB30 that went into my boat was probably 30 yrs old and no matter how much cleaning you get done it will not remove all the old broken down rusty crap that has had that time to build up inside its cooling system, which it seems, is quite alot.

P.S. Numbers Farkern

Look at a radiator filter while your getting it ready, after my rebuild it caught a fair bit or sealants and other crap, even after the chemical clean it still collects bits of crud that would have other wise gone through the water pump and maybe got stuck in the radiator.

TEFBA Radiator / Cooling system Filters

Like dis > http://www.ebay.com....=item20bddab6b4

I have one mate. I can't get the bloody thing open haha.

Going out tomorrow to see what the latest is. w00!

engine036.jpg

Here is something interesting

Here I was stressing about valve to piston clearence with the 1.5mm OS valves. Now with a 0.9 mm head gasket (smallest I could find), squish of 29 thou and cams with over 10.8 mm of lift the clearence on the intake was 2.2 mm and OVER 3 mm on the exhaust. I could have not relieved them :( So much for Tomei's "Over 10.8 mm relieve the pistons" GRRRRRRRRRRRR

Hi Piggaz,

just curious what your cam centerlines, lift and duration were set at for this

OK. I was out there today, all coming along. New oil cooler core and lines were going in. I changed the core because the old one would have been full of N1 oil pump gears!

I suspect startup and run in is Monday/Tuesday. I have some pics that I took today so i'll throw them up soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...