Jump to content
SAU Community

Recommended Posts

52 minutes ago, r32-25t said:

This all started cause a gearbox broke,

I think it was actually 4 but that's in the past and right now if I want to drive mine I go to the garage and turn the key :)

And when yours wasn't running, I could have wandered out the back, pushed the boat out and rip skidz too. Your car was off the road for a similar time wasn't it? ?

The car was pulled off the road running. I could have whacked a stock box in it, replace the turbo and it would have running within a couple weeks. 

14 minutes ago, Piggaz said:

And when yours wasn't running, I could have wandered out the back, pushed the boat out and rip skidz too. Your car was off the road for a similar time wasn't it? ?

The car was pulled off the road running. I could have whacked a stock box in it, replace the turbo and it would have running within a couple weeks. 

Can't remember it was a few years though  was about the same time you broke your engine I think 

3 minutes ago, ActionDan said:

Ok ladies simmer down.

Time to start taking bets on the power figure.

Apparently 480 AWKW was the most power out of a 8374 awkw (out of an Evo) Scott has seen on his dyno.

Nick (3.0/8374) went 461, 24 psi

Pete (3.2/vcam/8374) went 457awkw, 25 psi tapering back to 21 psi (120,000 turbine speed).

I don't know. It's all dictated by that magic 127,000 RPM turbine speed. What will be more interesting will be the boost level that it'll need to get there. Going off the -5 setup, it went 441 at 19 psi. Realistically, I should have just left it there.  Boost level I'm gonna peg at no more then 25 psi, tapering back down. 

26 minutes ago, Piggaz said:

Apparently 480 AWKW was the most power out of a 8374 awkw (out of an Evo) Scott has seen on his dyno.

Nick (3.0/8374) went 461, 24 psi

Pete (3.2/vcam/8374) went 457awkw, 25 psi tapering back to 21 psi (120,000 turbine speed).

I don't know. It's all dictated by that magic 127,000 RPM turbine speed. What will be more interesting will be the boost level that it'll need to get there. Going off the -5 setup, it went 441 at 19 psi. Realistically, I should have just left it there.  Boost level I'm gonna peg at no more then 25 psi, tapering back down. 

i know another evo making 450kw 8374 .92 internal gate at 36 psi

why stop at 25 psi

5 minutes ago, usmair said:

i know another evo making 450kw 8374 .92 internal gate at 36 psi

why stop at 25 psi

Because of turbine speed.

127k max. If it reaches that, the turbo is done, irrespective of pressure. 

Its no secret that these things have certain parameters to keep within, just like any mechanical part.

What speed are you at with your 30 or 32 psi?

Just now, Piggaz said:

Because of turbine speed.

127k max. If it reaches that, the turbo is done, irrespective of pressure. 

Its no secret that these things have certain parameters to keep within, just like any mechanical part.

and you know 25 = 127k?

is it to keep them alive or are you saying it wont anymore power beyond 127k

i was about to turn mine up to 34psi haha

Just now, usmair said:

and you know 25 = 127k?

is it to keep them alive or are you saying it wont anymore power beyond 127k

i was about to turn mine up to 34psi haha

No I don't know 25 psi will equal 127K. It was an educated guess... I could be well off. We will know because the speed sensor will be going back to the ecu.

Hopefully the wheel doesn't end up out the back of the exhaust. You're bloody crazy to turn it up that much without knowing what it's spinning at. Not the turbo's fault it if fails.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...