Jump to content
SAU Community

Recommended Posts

Okay about 2 months ago I had got the dodgy exhaust system one of the previous owners put on ripped off and redone.

2.5inch, high flow cat, 1 resonator. But I left the cannon on it because I couldn't afford anything more at the time...

Obviously the thing to too f**king loud, I didn't really care and got used to it. Clearly the cops didn't.

Today I got pulled over, yada yada, $88 fine and EPA will send you a letter in a month.

The plan now is to rip the cannon off and throw on a twin tip muffler. The question is, will this pass through EPA? (Provided it is under 90db).

Thanks in advanced.

EPA emissions? that is the letter in the mail one? they dont look for noise just the emissions the car emits defect for exhaust noise and having to go get a check to make sure its 90db is the one you should hope it is? should be easy to pass if it dosent you need another muffler or resnator in it

90db isnt very loud at all, one resonator and a twin tip muffler is wat i run and i dont think mine would be under 90.

best bet would have it tested somewhere... judt dont know were ud dtsrt

  • 3 weeks later...

"... the vehicle bearing Registration Number XXXXXX is excessively noisy and therefore likely to be exceeding the legal noise levels for the vehicle..."

"The noise test and anti-tampering inspection must be undertaken by an EPA approved Mechanic by the compliance due date which is Wednesday, 23 May 2012"

"- the engine test speed for your vehicle is 4800 rpm and the legal noise level for your vehicle is 90 dB(A)."

Again, I have a stock standard RB25DE with a K&N high flow panel filter, and a 2.5" exhaust system with a high-flow cat and 1 resonator + cannon (Will replace shitty cannon with twin tip muffler, hoping for less than 90 dB), stock extractors.

Will that pass the test? I'm just curious about the 'anti-tampering' part of it. Is a high-flow cat considered to be 'tampered' with?

Thanks.

would put money on you not passing with your current set up, my guess would be 97-98 decibels.

if you could get away with the plate that would work (again asking as they didn't see it. perhaps place behind the cat flange with 5 1cm holes drilled in it and only make the plate 1-2 mm thick)

*not sure on how many holes lol

Been there done that when I was on my Ps lol..

Best thing to do is borrow a standard exhaust from someone on the forums (heck im sure someone will lend you it for a day in exchange for a case of beers).

- Take off current loud exhaust

- Put on standard exhaust

- Go to EPA

- Pass inspection

- Put back old exhaust on and return borrowed exhaust

Your looking at about $50 for a case (depending on what your buddy prefers :P), $60 from memory to take the test and the $20 or odd you will be spending driving to pick up the exhaust and drop it back off.. Still adds up alot cheaper than paying a couple hundred and getting a whole new exhaust fabricated

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...