Jump to content
SAU Community

Recommended Posts

  • Replies 126
  • Created
  • Last Reply

Top Posters In This Topic

I've done heaps of divided turbo pipes, they do work but having done so many I also found a trick with the divider plate.

I leave a small section of the front turbos air path in plated, it allows some of the front turbos air to swirl around into the rear turbos path.

A customer of mine who is a fluid scientist type guy explained how making the front turbo swirl around the inside of the pipe before merging with the rear turbo helps promote a lamina flow and draw the air away from the compressor housing thus reducing the shuffle.

The mod does seem to improve the issue on all the cars I've ever done one for.

Can't hurt to give it a go.

Risking,

So if mine was to shuffle for some strange reason (people say it should be OK)....then to what level would the TT pipe mod cure the shuffling? Would it still be there a little bit or would it completely disappear?

Everyday I'm shuffling :D lol sorry had to throw that one in...

I've currently got t517z turbos and no TT pipe mod, no shuffle

I had the impression shuffling comes from bigger turbos (gtr-s, -10 etc)

LOL I've been waiting for that :D

Yeh same here. It's meant to happen with big efficient BB turbos that spool up a bit too much air down low and cause surging and stalling out of each other in a seesaw/back and forth fashion. That's how I understand it anyway :P Sort of similar to that shhh-shhh-shhh-shhh that it does when you back off the throttle very slowly at lowish RPM and on boost. ....i think.

I'm thinking I'll be fine.

Everyday I'm shuffling :D lol sorry had to throw that one in...

I've currently got t517z turbos and no TT pipe mod, no shuffle

I had the impression shuffling comes from bigger turbos (gtr-s, -10 etc)

What ECU do you have?

Ah damn, so there's probably a 50-50 split of people who've experienced shuffling and those who haven't with -9's

Ah there is one person in the thread, everyone else hasn't had an issue.

Not sure how that is a even split.

newb time... what exactly is shuffling and i'm assuming it's a bad thing from how this thread is referring to it?

As far as I know, shuffling is a thing where the two turbos will try to stall each other out down in low rpm ranges because they're creating too much air than what the engine can swallow. Both turbos are trying to force more air into the one overhead collecting pipe and that pressure will not always go to the intake mani but back down the other turbos xompress

Ah damn iPhone!

....was say that it will instead go back down the othe turbos compressor out let thus causing it to momentarily stall out. It's meant to happen with bigger, efficient bb turbos where the two turbs create too much boost down low...similar to surge. It's meant to give off a shoo shoo shoo sound when it happens...hope that helps ;)

I was thinking shuffle would happen easier with the smaller BB type turbs like the -7,-9 where they make boost very early in the rev range, say 2k-2.5k and the engine just simply cannot ingest that amount of air, and with the oem journals and the -5,-10 that do not start to make positive pressure so early it would not really be a problem.

With the -9s crusing along on 5th flat roads, just easing on the throttle at 2k ish is enough to make +ve pressure and you get shuffle. Ive never driven a car with -5s, but under the same conditions, does it make +ve pressure to induce shuffle?

I was thinking shuffle would happen easier with the smaller BB type turbs like the -7,-9 where they make boost very early in the rev range, say 2k-2.5k and the engine just simply cannot ingest that amount of air, and with the oem journals and the -5,-10 that do not start to make positive pressure so early it would not really be a problem.

With the -9s crusing along on 5th flat roads, just easing on the throttle at 2k ish is enough to make +ve pressure and you get shuffle. Ive never driven a car with -5s, but under the same conditions, does it make +ve pressure to induce shuffle?

That's all very true, just curious why in this particular thread you're the only one experiencing these problems? The majority seem to say that there're no issues with the smaller turbos in the GT2860 range.

Bearing in mind every set up is different and there are many factors that have to be considered eg. actuator preload(mine are f*ck tight) boost controller settings and as some have said tuning.....and hell, diff ratios for all I know

Also mine is not in a gtr, but everything is set up as normal beside for a 2.5" hot pipe from TT pipe to intercooler which I guess could be contributing.

Either way no biggie. There are some here who get it with oem turbs....

I've got gtrs, shuffle under higher load.

Went to a bigger exhaust, problems better.

Getting a modded TT pipe from risking soon, will report how that goes.

I've got a set of hks gt-rs on my 2.6l. 441awkw @ 24psi no shuffle at all. :)

Have had hks 2530s and no shuffle either all of this with no modification to twin turbo pipe or any other..

How did you get it to stop?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...