Jump to content
SAU Community

Recommended Posts

Hey guys, I've got an R32 GTS-4 and really keen on getting 18x9+20 on the fronts and 18x10+18 on the rears. But I want to make sure the rears will clear everything and there won't be any fitment issues with the rims hitting the insides of the car. Just wanna make sure that 10 inch wide rears wont affect the drive. Any advice would be very helpful. Thanks!

Edited by RoyceR32
Link to comment
https://www.sau.com.au/forums/topic/398423-staggered-fitment/
Share on other sites

I'm after stretch and poke as well so I'm chucking 225/40/18 on the front and 235/40/18 on the rear. Should look insane!

Fashion over function?

Will look even better up on the hoist with a burnt out transfer case being replaced

you ask for advice, here it is.

what they are saying is - you do what you like so it will "look" awesome.

right up until the 4wd poos itself and you have to repair/replace the 4wd transfer case.

the skyline attessa needs the same rolling diameter front and rear in order not to shit itself. You use different width/aspect ratio tyres at your own peril

and while I'm not here to tell you what to do - it's your car - i will say:

1. it looks shit

2. the camber you'll run will destroy tyres instantly

3. the wear on CVs, etc will be greater

4. you run the risk of damaging the rim much faster

5. it will be uncomfortable as an enima, so if it's your daily ride, good luck with that

...and probably a whole lot more issues.

But hey, what price to get the bitches (which, contrary to what car modifiers think, it won't help you. F&F has a lot to answer for).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
×
×
  • Create New...