Jump to content
SAU Community

Recommended Posts

Thanks Mick > Anthony > Peter.

I would have thought that one of you guys would have put it on 'Lay-by' before I appeared on the scene. ;)

This is how I received the steering wheel a couple of weeks ago.

Terry-51_zps80e16553.jpg[/url]

After doing a few adjustments, the steering wheel now looks like this...

Terry-52_zps62ea1e28.jpg

In keeping with the old look of the early 90s...

Terry-53_zpsbd2a0490.jpg[

Now to see if a trimmer can fix the thumb pads

  • Like 2

My 2c. I'm a bit under impressed with it Terry. Especially for that price.

Does not look to have been well looked after :/

But I'm sure if you decided to go for it and get it for the right price that you could bring it back :thumbsup:

Edited by Sinista32

Thanks Mick > Anthony > Peter.

I would have thought that one of you guys would have put it on 'Lay-by' before I appeared on the scene. ;)

This is how I received the steering wheel a couple of weeks ago.

Terry-51_zps80e16553.jpg[/url]

After doing a few adjustments, the steering wheel now looks like this...

Terry-52_zps62ea1e28.jpg

In keeping with the old look of the early 90s...

Terry-53_zpsbd2a0490.jpg[

Now to see if a trimmer can fix the thumb pads

If you do want it, ME TAKE! and even pay for it :)

i bought some nismo s-tune pads for my s14 a while ago. Haven't noticed much improvement over stock, except massive increase in dusting... and they were $250 a pair :whistling:

Powdered Nismo!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...