Jump to content
SAU Community

Recommended Posts

It's fine. But unless it's the only fuel available, there's no point in using it.

91 all the way for a DE. There will be little to no benefit running 98 or 100 ron fuel.

10:1 is hardly high compression.

A 2ZZ-FE in a base model Corolla is 10.0:1 and requires 91 only. A Lancer VR-X is 10.5:1 and only requires 91. XT Falcon, 10.3:1 and only requires 91.

I'm not sure what makes the 25DE require higher RON fuel?

"Requires" and "runs best on" are two very different things though.

My VQ35de Stagea is 10.3:1 comp and requires a minimum of 95 although I will only be using the United 100 (and maybe a 98 every now and then).

The Wife's 380is 10.0:1 and "requires" only 91, but I can tell you that there is a massive difference when you run 95 and then an even larger jump when running 100 (as per the timing advance and engine load display via Torque on my phone).

Aren't the tuned for the use of Japans fuel?

Which is higher in octane than here?

They are the AU delivered ones, and of course a Falcon. They require 91 RON that we get here.

"Requires" and "runs best on" are two very different things though.

My VQ35de Stagea is 10.3:1 comp and requires a minimum of 95 although I will only be using the United 100 (and maybe a 98 every now and then).

The Wife's 380is 10.0:1 and "requires" only 91, but I can tell you that there is a massive difference when you run 95 and then an even larger jump when running 100 (as per the timing advance and engine load display via Torque on my phone).

I think you'll find it's mostly placebo affect.

Most ECUs don't have enough scope for self tuning to make any user of higher RON fuel. Note, I said most. I'd be surprised if an RB25DE could.

I too would be surprised if the RB25de ecu could make use of the higher octane fuel, but no harm in using a better fuel for a couple of bucks per tank IMO.

No placebo effect with regards to the two cars listed above (particularly the 380 - cleaver little ecu that one) although I am talking about 2005 ecu's as opposed to a late 90's ecu.

RB25DE on an R34 requires minimum of 95RON - Says on the manufacturer's brochure and on the manual. But if you need emergency fuel, I can't see any reason why 91 would cause major issues for short term use.

Oddly enough I still get some pinging on 95 and throttle response is not as crisp :unsure:

I always fill 98 myself - No pings and better economy. But I must stress the price of 98 will not make it cheaper to run vs. running 95.

Filling up with 100 or higher is a waste imho.

I believe by filling 98 you will be hitting the limits of the stock ECU and sensors - Filling 98 just guarantees you are definatly well within the 95+ range.

Aren't the tuned for the use of Japans fuel?

Which is higher in octane than here?

pretty sure their base fuel isn't any higher than here, they just have a premium fuel that is higher than what we have here. so they still have 91 octane fuel over there.

pretty sure their base fuel isn't any higher than here, they just have a premium fuel that is higher than what we have here. so they still have 91 octane fuel over there.

Ahhh ok.

Marc, you really need to stop posting useful shit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...