Jump to content
SAU Community

Automatic Door Lock At 25Kph


trickytiger
 Share

Recommended Posts

Hi,

I've been thinking a bit about the automatic door lock at 25kph on the r33's

There is 4 wires at each door solonoid, so is it possible that one of these wires could send the 25kph lock signal to the solonoid? if it does it means at each solonoid we can just cut a wire to disable the feature on each door so that we can also keep the rear demister.

Maybe someone here knows what each of these 4 wires are. I know from when i put an actuator in the drivers door that there appears to be no unlock wire going to them.

Link to comment
Share on other sites

Hi,

I've been thinking a bit about the automatic door lock at 25kph on the r33's

There is 4 wires at each door solonoid, so is it possible that one of these wires could send the 25kph lock signal to the solonoid? if it does it means at each solonoid we can just cut a wire to disable the feature on each door so that we can also keep the rear demister.

Maybe someone here knows what each of these 4 wires are. I know from when i put an actuator in the drivers door that there appears to be no unlock wire going to them.

It's a feature on these skylines that when you go over 25kph your doors automatically lock which is kinda annoying. I'm trying to find a solution other than the one that's already known which is cutting a green wire at the smart entrance module, which also disables the rear demister...

Link to comment
Share on other sites

I think it's a safety thing to keep unwanted passengers from getting in.I like it,being female and driveing all the time on my own,

it makes me feel safe.

Link to comment
Share on other sites

Yep Factory.

My S2 33 Sedan, at 25k's locks all 4 and if you try to unlock while driving, they lock straight away.

Doesn't unlock when I stop and switch the ignition off and I always go to get out but can't til I flick the switch.

Found this thread about it too.

http://www.skylinesa...3%20door%20lock

Edited by Not a Pulsar
Link to comment
Share on other sites

My drivers door never had it but my passenger door used to lock at around 20kmh

then one day the passenger door solenoid stuffed up so I got one from a S2 R33 (NA) and put it in my S1 and it never locked above 20kmh since. So think the OP Might be on to it as I'm pretty sure theres one less wire on the S2 Solenoid as it might be done from elsewhere in the S2's

Link to comment
Share on other sites

My drivers door never had it but my passenger door used to lock at around 20kmh

then one day the passenger door solenoid stuffed up so I got one from a S2 R33 (NA) and put it in my S1 and it never locked above 20kmh since. So think the OP Might be on to it as I'm pretty sure theres one less wire on the S2 Solenoid as it might be done from elsewhere in the S2's

That sounds hopeful :) will test with the passenger door after work to find out if this idea will work

Link to comment
Share on other sites

Unfortunately this idea has proven not to be a solution. there is only two wires that control the unlock and lock functions, you can cut both the other two and it will still lock and unlock... so i wonder what the other two wires are there for?

Link to comment
Share on other sites

Have just thought of another way this may be possible. Reverse the lock and unlock wires at each solonoid, this way hopefully when you hit 25Kph the car would be checking to make sure the doors are unlocked and if not unlock them.

Will just go out to the car and test this.

Link to comment
Share on other sites

on this relative topic. My 25kmph passenger door locking always has and still works.

But my rear demister has stopped working. Fuse is fine too though.

thoughts andybody?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Opened up the cluster to inspect the gauge itself for signs of damage and it looks good. Got curious since that needle doesn't go back to a "neutral" position by itself (it stays in the same position when ignition is off. so I manually moved it to 1/2. Connected it back, turned on the ignition and the needle started moving up! Not sure what's up with that but before that the needle was way down below empty like fully south west. There's always a chance that the needle moved slightly the first time I tried and I didn't notice because of how slowly it moves and how far it was from the markings. I don't know if the current needle position is accurate so I'll fill it up and see where that brings it. I guess I'll try to adjust it manually if it doesn't get to F. Looks like the needle position is relative and not absolute? Thanks all for your help and patience!
    • You're confusing two different responders and more than one issue. The stock Neo ECU boost sensor is used by the ECU for protection purposes. It is essentially only an overboost sensor. It is not used for determining engine load for fuelling or ignition purposes. That task falls solely to the AFM. Any aftermarket ECU that either has an onboard MAP sensor or a plug in one, will use the MAP sensor as the primary load sensor. Or I should perhaps say "can", rather than "will", because some of them have the option of using other primary load sensors. That MAP sensor is not for the same function as the stock Neo boost sensor. The reason I recommended against a plug and play ECU is that they are intended to run a particular engine and usually in the car that the particular engine came in. So, if you have a transplanted engine in a different car, with some parts of the original missing (such as the boost sensor, for example) and therefore likely non-standardness of the loom and its insertion into the car's loom, then it is very likely that you will run into the same problems with needing to fix up wiring to make it work that you would with the stock ECU. And, if doing so for the stock ECU is enough of an obstacle that you start considering a standalone plugin as a solution, it should become clear that the plugin is quite possibly not the solution you'd hope it to be. It would just lead to more of the same type of problem solving work to get it going. In the above paragraph and in my earlier post, the lack of the boost sensor is not critical. It was just used as an example of something that we knew you did not have right, such that the stock ECU would not work. I took that as an indicator of a reasonable probability that there were other related problems hiding there.
    • I can think of two places in my city of <1.5million population that specialise in automotive instrument repairs.Unless you're out in the wilds of Quebec, you have 3 major Canadian and 3 major US cities within the same distance as the single nearest city to mine. Surely there is somewhere you could send it.
    • I never cared for twins but whenever these conversations came up, I always presumed the higher number represented a larger turbo. Learn something new everyday. 
    • Interesting, I've never seen a failure like that before but with the age of these cars and the general questionable-ness of all kinds of parts these days you can't rule anything out I suppose. Boost leak testing the boost control system would've revealed this though.
×
×
  • Create New...