Jump to content
SAU Community

Recommended Posts

Hi,

I've been thinking a bit about the automatic door lock at 25kph on the r33's

There is 4 wires at each door solonoid, so is it possible that one of these wires could send the 25kph lock signal to the solonoid? if it does it means at each solonoid we can just cut a wire to disable the feature on each door so that we can also keep the rear demister.

Maybe someone here knows what each of these 4 wires are. I know from when i put an actuator in the drivers door that there appears to be no unlock wire going to them.

Link to comment
https://www.sau.com.au/forums/topic/404329-automatic-door-lock-at-25kph/
Share on other sites

Hi,

I've been thinking a bit about the automatic door lock at 25kph on the r33's

There is 4 wires at each door solonoid, so is it possible that one of these wires could send the 25kph lock signal to the solonoid? if it does it means at each solonoid we can just cut a wire to disable the feature on each door so that we can also keep the rear demister.

Maybe someone here knows what each of these 4 wires are. I know from when i put an actuator in the drivers door that there appears to be no unlock wire going to them.

It's a feature on these skylines that when you go over 25kph your doors automatically lock which is kinda annoying. I'm trying to find a solution other than the one that's already known which is cutting a green wire at the smart entrance module, which also disables the rear demister...

Yep Factory.

My S2 33 Sedan, at 25k's locks all 4 and if you try to unlock while driving, they lock straight away.

Doesn't unlock when I stop and switch the ignition off and I always go to get out but can't til I flick the switch.

Found this thread about it too.

http://www.skylinesa...3%20door%20lock

Edited by Not a Pulsar

My drivers door never had it but my passenger door used to lock at around 20kmh

then one day the passenger door solenoid stuffed up so I got one from a S2 R33 (NA) and put it in my S1 and it never locked above 20kmh since. So think the OP Might be on to it as I'm pretty sure theres one less wire on the S2 Solenoid as it might be done from elsewhere in the S2's

My drivers door never had it but my passenger door used to lock at around 20kmh

then one day the passenger door solenoid stuffed up so I got one from a S2 R33 (NA) and put it in my S1 and it never locked above 20kmh since. So think the OP Might be on to it as I'm pretty sure theres one less wire on the S2 Solenoid as it might be done from elsewhere in the S2's

That sounds hopeful :) will test with the passenger door after work to find out if this idea will work

Unfortunately this idea has proven not to be a solution. there is only two wires that control the unlock and lock functions, you can cut both the other two and it will still lock and unlock... so i wonder what the other two wires are there for?

Have just thought of another way this may be possible. Reverse the lock and unlock wires at each solonoid, this way hopefully when you hit 25Kph the car would be checking to make sure the doors are unlocked and if not unlock them.

Will just go out to the car and test this.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day  
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
    • Are you 100% sure this isn't tune related?
    • 140-150 across the board. At this point hoping the grounding harness fixes it. My grounds are all tied to the chassis and none to the battery. For SR and KA that’s never been a problem for me but had a few other guys here and Reddit who told me RB really like a very solid ground setup tied to the battery so going to try that next, I’m stumped if that doesn’t do it. Never had a car have spark and fuel and not fire off before. Only thing I can think is the spark is intermittent/weak because of grounds nothing else really makes sense at this point 
    • I am having close to the same issue. Can you help me with what wire you grounded to get your pump to trigger?
×
×
  • Create New...