Jump to content
SAU Community

Boost Controller And Gauge Install Queries

rb2534

By rb2534,
in Engines & Forced Induction

 Share

Recommended Posts

rb2534 Rising Star

rb2534

Posted
Posted

Hey just fitted a electronic boost controller to my 34 and have a few queries.

Firstly the manual says to use the fuel pressure reg as a source for the vacuum, but I had a blonde moment and tee'd it in on the vacuum line that runs between the manifold and that fuel valve that runs to the fuel filter. Can't find the name but it sits just above the fuel pressure reg and as I said it returns to the fuel filter. I assume it increases the flow of the fuel when the engines under load/boost.

My controller seems to be working ok but just to confirm is this ok or should I run it directly between the fuel pressure reg and the manifold?

Secondly I'm looking to install a boost gauge, now since i've used a line going off the manifold for the vacuum source would it be ok to use the line that runs from there to the back of the boost controller to tee in the boost gauge?

The way I see it instead of running a line all the way between the actator and solenoid with the gauge tee'd in between the manifold and the controller the gauge will be seeing manifold pressure which is the same as the boost controller.

Am I totally wrong and will this not work and cause problems with the controller functioning properly?

Cheers for any help

89CAL Grand Master

89CAL

Posted
Posted

Any boost source off the manifold is fine. I'd rather not take it from the Fuel pressure reg cause then thats two lines that can split and result in incorrect fueling due to the FPR getting the wrong boost reading

Boost gauge is the same thing. And yes my theory is its best if your gauge and controller are both seeing the same boost from the same source. You cant hook your boost gauge into the line that runs to the actuator as this is taken off the IC piping usually which means it wont really see vaccum.

Manifold pressure will be needed for both controller and gauge. And taking them from the same spot is the best to ensure there both seeing the same boost

GTSBoy Grand Master

GTSBoy

Posted
Posted

There is a line off the back of the plenum that runs to the car's own MAP sensor (used for the dash gauge, and in the case of the R34, there's a second MAP sensor that the ECU uses to look at boost). This line makes sense to tee into, as you know that it sees proper manifold pressure, and it is not associated with the FPR (and the inherent risk of losing all vital MAP sensing at the same time, as stated by Cal above).

rb2534 Rising Star

rb2534

Posted
  • Author
Posted

Yeah I see your point ill find another source for the Boost gauge and the controller off the manifold I've seen a few people hook up boost gauges off the back of the manifold somewhere near the brake booster.

Cheers

  • 1 year later...
V28VX37 Veteran

V28VX37

Posted
Posted

I thought I'd resurrect this thread rather than starting a new one. An EBC seems pretty easy to install but I've got a couple of questions as I haven't done one before.

I just got a second hand Blitz Dual-SBC Spec R EBC (thanks fantov!) to replace the current boost controller, a TurboTech V2, on my R34 GTT. This is the Blitz that comes with the big black dual solenoid box:

post-15500-0-64083100-1390899568.jpg

My current manual boost controller is tee'd off between the intake manifold and stock BOV, with the out pipe running to the turbo actuator. Do I just replace it with the new solenoid?

The Blitz manual also says the following:

For vehicles equipped with a stock solenoid, locate the factory T and remove the factory solenoid line from the factory "T". Then cap off the stock solenoid line. Leave the factory solenoid in the vehicle still connected to factory electrical harness.

Where's the stock solenoid? Will disconnecting this upset my ECU or Nistune?

Also, if I was to set the EBC close to the same setting as my manual boost controller (around 17psi), would it work ok without touching up the tune? Or is this kind of thing best done on the dyno? I don't have a boost gauge in the car and certainly don't want to overboost it...

The Blitz manual is available here. Thanks and sorry about all the newbie questions :)

Kane_R32 Experienced

Kane_R32

Posted
Posted

1) get the vacuum source off the intake manifold. That way the EBC sees the total boost after any boost drops (FMIC etc)
2) I wouldn't use the hose from intake manifold to bov for the solenoid. I would locate where the factory solonoid picks its boost source from and run off that.

V28VX37 Veteran

V28VX37

Posted
Posted

1) get the vacuum source off the intake manifold. That way the EBC sees the total boost after any boost drops (FMIC etc)

2) I wouldn't use the hose from intake manifold to bov for the solenoid. I would locate where the factory solonoid picks its boost source from and run off that.

Thanks! So by the looks of things, the line that currently runs into the manual boost controller (from between manifold and BOV) should go to the Blitz controller (i.e. vacuum source).

Can someone confirm which connector is IN and which is OUT in the stock solenoid? I've currently got the bottom hose disconnected (uncapped), I'm guessing that could be the actuator line? See pics below.

12405345963_d7aa45ede5_z.jpg

12405654104_30db2d214e.jpg

12405652814_b4fe530ed7_o.jpg

Kane_R32 Experienced

Kane_R32

Posted
Posted

Yeah you could keep that "t-peice" from manifold to bov for the vacuum source if you like.

Regarding the solenoid set-up. From the manifold should be your "in" and to the actuator should be your "out"

V28VX37 Veteran

V28VX37

Posted
Posted

Yeah you could keep that "t-peice" from manifold to bov for the vacuum source if you like.

Regarding the solenoid set-up. From the manifold should be your "in" and to the actuator should be your "out"

Thanks!

I'm still trying to work out which connector on the stock solenoid is 'in' and which is 'out', anyone know?

Also, where's the 'in' line to the stock solenoid connected to, in the standard setup?

V28VX37 Veteran

V28VX37

Posted
Posted (edited)

It's only an air valve, it doesn't matter.

Just make sure you have the restrictor in the hose or boost will skyrocket on the stock setup.

Thanks Scott. I'm only asking because the Blitz dual solenoid has clearly marked In and Out, just want to make sure it'll be connected 100% correct.

EDIT: Another question for you Scott: I assume I can keep the stock solenoid wired in (electrical) even with the hoses removed? This shouldn't confuse the ECU/Nistune, should it?

Edited by V28VX37
scotty nm35 Grand Master

scotty nm35

Posted
Posted

I assume I can keep the stock solenoid wired in (electrical) even with the hoses removed? This shouldn't confuse the ECU/Nistune, should it?

Will be the best way, and run some fake hoses to somewhere, so they look like they are connected to something, otherwise you could get defected easily.

If you unplugged it you would throw an error code (on the stock computer) but I assume the Nistune can fix that in the software.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...