Jump to content
SAU Community

Recommended Posts

  • 8 months later...

Hey all,

Just wanted to ask a quick one about fuel filters. What are you guys using these days? I've read a number of older posts about using the standard Ryco filters, some good some bad. I'm also aware of the situation with needing to replace fuel filters regularly just after switching to E85 until the system is clean. So right now I'm considering three paths.

1. I stick with the Ryco paper filter and just replace it regularly.

2. I stick with the Ryco paper filter for now, then after my first tank of E85, switch to a billet filter (Aeroflow, Speedflow, Proflow, or similar?)

3. I switch to a billet filter now, before getting the E85 tune.

At the moment I'm leaning towards option 3 for a couple of reasons. Firstly I have the standard feed line to my Ryco filter, then a -6 fuel line to my HKS rail. It works, but considering the Ryco filter has 5/16 push on barbs, it doesn't quite fit as nicely as I would like. With the billet filter I could use a -6 AN fitting on one side, and a -6 AN to 5/16 tail barb on the other side. Second, if I need to replace filters regularly, would a washable element not be a cost effective solution?

  • Like 1

I use twin -6 an stainless mesh filters, Proflow ones, they cost around $100 each though plus fittings. No issues in 3 years daily driving on United mainly, and they have never been cleaned.

Do you know what micron filter element you've got, Scott?

Another one, where are people mounting their GM flex-fuel sensors? I've got the flow through type and I thought I could mount it between my regulator and return line in the engine bay, but I can't see it happening. This thing is quite hard to mount with the factory hard lines :glare:

Do you know what micron filter element you've got, Scott?

Another one, where are people mounting their GM flex-fuel sensors? I've got the flow through type and I thought I could mount it between my regulator and return line in the engine bay, but I can't see it happening. This thing is quite hard to mount with the factory hard lines :glare:

In the boot. Tee off the return line just before it drops back into the tank. Hidden sensor FTW!

In the boot. Tee off the return line just before it drops back into the tank. Hidden sensor FTW!

Yeh? I did think of putting it there. Could maybe work something out... All seems a bit tight though, I can hardly see my return line let alone find a place to put two tees into it :/

Edited by Hanaldo

Yeh? I did think of putting it there. Could maybe work something out... All seems a bit tight though, I can hardly see my return line let alone find a place to put two tees into it :/

BRB, taking a photo for you :P

I think it's 100 micron mesh.

Don't you want the sensor as close to the rail as possible?

I can't see how it makes any difference. Either way, once the fuel is mixed, it's the same. Just dontn belt it until you see the reading settle.

Ah, you got the little small thing.

Yeh so they say. Its fkn massive! Ideally I would mount it close to the rail, but I can't see it fitting anywhere unless I remote mount the sensor and run like 2 meters of hose to it :/

Yeh so they say. Its fkn massive! Ideally I would mount it close to the rail, but I can't see it fitting anywhere unless I remote mount the sensor and run like 2 meters of hose to it :/

Under the car?

Just curious why I've seen a few setups with the flex sensor mounted in the boot? Another car I've seen setup by UNIGROUP has the flex sensor in the boot too?

What are the benefits? Is it just a convenience thing or heat stress thing?

Just curious why I've seen a few setups with the flex sensor mounted in the boot? Another car I've seen setup by UNIGROUP has the flex sensor in the boot too?

What are the benefits? Is it just a convenience thing or heat stress thing?

It's one less thing in an already full engine bay. No other reason.

How many free 0-5V inputs do you need on your ecu? The zeitronix Eca kit outputs fuel temp and ethanol % doesn't it?

1 I'm pretty sure. And yes fuel temp too. You can set up fuel temp correction too

Under the car?

Yeh this is what I was thinking of. It would be so much easier if I could cut the standard hard line, but I don't want to lose the flared end.

I think the easiest thing would just be to run a longer length of hose to the sensor. Just seems such a messy way of doing it :/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...