Jump to content
SAU Community

Recommended Posts

Hi Guys,

Ok I've got some used spare parts and I'm prepared to let them go pretty cheap to free up some space in the garage.

2010 OEM 20 inch wheels with 50% used Dunlop's - $3,000 (There are a few scratches on two of the wheels. Easily fixed if repainted though)

Full exhaust - $2,500

80 mm straight through dump pipes

100 mm twin resonated midpipe

90 mm Rear section Inc two mufflers

This is the full exhaust that I ran on the car at Bathurst last November. Its not going to save you as much weight as a titanium system would but its still much lighter than stock and It's super quiet for daily driving but when you get the power down it comes on song very nicely. It's good for up to 800 hp. I'm selling it because I need something lighter. here is a clip of how it sounds

2x OEM Front seats - $5,000 for both

2x OEM Doors white - $5,000 for both

1xOEM Bonnet white - $3,000

2xOEM Turbo Chargers - $4,000 for both

Give me a call or email if your interested.

0418 290 615

[email protected]

Miles..

  • 2 weeks later...
  • Replies 227
  • Created
  • Last Reply

Top Posters In This Topic

Dodson built transmission for sale. CLICK HERE!

I have a fully built Dodson GR6 transmission

Parts list below, pretty much the full Dodson Catalog.

our race only car is going to a lightweight specially adapted rear wheel drive transmission which is a change in direction after our new transmission was just finished being built in December. The transmission has never been used (other than the standard Run in and check by the Dodson authorised Technician test car). Also has all the new Dodson tranny and diff oils. ATS Carbon Rear diff.

All the parts are brand new. Read: Brand new promax clutch, Brand new 1-6 straight cut greatest. and all the parts listed below.

We also have a a billet transmission selector fork installed (this is the fork that failed in my transmission originally)

I don't need a transmission swap but will consider if it makes the sale.

The full build cost and supply of a second hand transmission would fetch AU$55,000

Will sell for $49,000.

Steve Thatcher From JustJap in Sydney (the Dodson authorised australian technicians) will happily answer any questions/verify the work and the install. his email is:

Steve Thatcher [email protected]

R35 CPM PRO MAX COMPLETE CLUTCH 1000 FT/LBS+

R35 MC1 2MM MECHANICAL CIRCLIP 1 2MM

R35 MC2 MECHANICAL CIRCLIP 2

R35 GL GEAR LOCK FOR FWD TRANFER GEAR

R35 ORK O RING KIT

R35 OPK OIL PUMP UPGRADE AND REPAIR KIT

R35 DCS HIGH TEMP DIFF SIDE COVER SEAL

R35 TP BILLET ALLOY TRANSMISSION PAN/SUMP includes R35MK

R35 TF TRANSMISSION FILTER REUSEABLE

R35 TFP TRANSMISSION FLUID + 30 DEG AMBIENT

R35 DO1 HEAVY DUTY DIFFERENTIAL OIL

R35 ETS ENGINE TEMP SWITCH 68 DEG C

R35 RSS HEAVY DUTY CLUTCH RETURN SPRING SEAL

R35 OPP OIL PUMP END PLATE AND GASKET

R35 6SGS SC 6 SPEED GEAR SET STRAIGHT CUT

R35 FWDCH FWD UPGRADED CLUTCH HOUSING

R35 FWDCP FWD UPGRADED CLUTCH

R35 FWDP FRONT WHEEL DRIVE PINION

R35 FOS FWD OUTPUT SHAFT

hi all have a set of RS-D up for sell

20 x 9.5 +40 x2

20 x 10.5 +12 x 2

colour is black with chrome lip

condition is (brand new condition) no marks or scratches on the lip or spokes itself

remarks: only lock nut mark inside the lock nut hole.

asking $4900

post-4074-0-27086700-1332818305_thumb.jpg

post-4074-0-04170700-1332818321_thumb.jpg

post-4074-0-91996100-1332818338_thumb.jpg

post-4074-0-19538200-1332818352_thumb.jpg

1331547821[/url]' post='6271583']

Dodson built transmission for sale. CLICK HERE!

I have a fully built Dodson GR6 transmission

Parts list below, pretty much the full Dodson Catalog.

our race only car is going to a lightweight specially adapted rear wheel drive transmission which is a change in direction after our new transmission was just finished being built in December. The transmission has never been used (other than the standard Run in and check by the Dodson authorised Technician test car). Also has all the new Dodson tranny and diff oils. ATS Carbon Rear diff.

All the parts are brand new. Read: Brand new promax clutch, Brand new 1-6 straight cut greatest. and all the parts listed below.

We also have a a billet transmission selector fork installed (this is the fork that failed in my transmission originally)

I don't need a transmission swap but will consider if it makes the sale.

The full build cost and supply of a second hand transmission would fetch AU$55,000

Will sell for $49,000.

Steve Thatcher From JustJap in Sydney (the Dodson authorised australian technicians) will happily answer any questions/verify the work and the install. his email is:

Steve Thatcher [email protected]

R35 CPM PRO MAX COMPLETE CLUTCH 1000 FT/LBS+

R35 MC1 2MM MECHANICAL CIRCLIP 1 2MM

R35 MC2 MECHANICAL CIRCLIP 2

R35 GL GEAR LOCK FOR FWD TRANFER GEAR

R35 ORK O RING KIT

R35 OPK OIL PUMP UPGRADE AND REPAIR KIT

R35 DCS HIGH TEMP DIFF SIDE COVER SEAL

R35 TP BILLET ALLOY TRANSMISSION PAN/SUMP includes R35MK

R35 TF TRANSMISSION FILTER REUSEABLE

R35 TFP TRANSMISSION FLUID + 30 DEG AMBIENT

R35 DO1 HEAVY DUTY DIFFERENTIAL OIL

R35 ETS ENGINE TEMP SWITCH 68 DEG C

R35 RSS HEAVY DUTY CLUTCH RETURN SPRING SEAL

R35 OPP OIL PUMP END PLATE AND GASKET

R35 6SGS SC 6 SPEED GEAR SET STRAIGHT CUT

R35 FWDCH FWD UPGRADED CLUTCH HOUSING

R35 FWDCP FWD UPGRADED CLUTCH

R35 FWDP FRONT WHEEL DRIVE PINION

R35 FOS FWD OUTPUT SHAFT

Price drop

$45,000 without tranny swap

$37,000 with a good condition tranny swap

Hi everyone,

I have for sale a brand new OEM Nissan R35 GTR car cover with carrycase. Purchased from USA but was never used.

Asking $300, however open to offers. Below is the ebay link;

My link

Item is located in Norwest NSW 2155 (just off the M7).

If your interested please contact me on 0411 415 644.

Rohin

Edited by Admin.

If you wish to advertise the parts you are selling on this forum, you are required to become a business trader.

See the following thread for further information:

http://www.skylinesaustralia.com/forums/topic/294953-are-you-a-business-want-to-advertise-on-sau-click-here/

ok standard width top racing front bumper and carbon fenders going out the door $3500 for the lot excl shipping. otherwise they are off to Dubai by next week!

thats AU7000 of carbon parts adn AU2000 shipping from hong kong - its a steal

Hi mate,

Is this still available? I am in Hong Kong and can pick up from Top Racing.

Thanks

Rob

Hi Guys, Sold the R35 and have left

a brand new Greddy R35 motor shrink wrapped that I kept as a spare, $14,000

a set of brand new set of Run flat R35 tyres from USA in plastic $2000

Im in Northmead near Parramatta Sydney NSW.

Dom 0414 62 62 43

And the new race car has 306.1 kwatts ATW weighs 100+kgs less than an R35 and does eastern creek in about 2 mins in the dry and 3 mins in the wet using 3 sets of rear tyres per lap. But boy is it fun.

So what is it?

Hi Guys, Sold the R35 and have left

a brand new Greddy R35 motor shrink wrapped that I kept as a spare, $14,000

a set of brand new set of Run flat R35 tyres from USA in plastic $2000

Im in Northmead near Parramatta Sydney NSW.

Dom 0414 62 62 43

And the new race car has 306.1 kwatts ATW weighs 100+kgs less than an R35 and does eastern creek in about 2 mins in the dry and 3 mins in the wet using 3 sets of rear tyres per lap. But boy is it fun.

So what is it?

Wow you must change tyres quickly.

  • 3 weeks later...

2 x 2008 model Black Edition GTR seats (grey with red inserts) in as new condition

1 x 2008 set of brakes (several sets of second hand discs AP/stock mainly stuffed) - all working fine 12,000km from new

1 x 2012 set of brakes as new (travelled under 100km)

Make me an offer....

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...