Jump to content
SAU Community

Cross Threaded Spark Plug Hole

Plattsy

By Plattsy,
in General Maintenance

 Share

Recommended Posts

Plattsy Grand Master

Plattsy

Posted
Posted

Whats the best fix gents, geezer I know has a cross threaded spark plug which may be causing a miss fire, it's on the 6th cylinder so it's a pain int the arse to get too, but can this be tapped or re plugged?

Link to comment
https://www.sau.com.au/forums/topic/405141-cross-threaded-spark-plug-hole/
Share on other sites
Plattsy Grand Master

Plattsy

Posted
  • Author
Posted
  On 19/07/2012 at 9:46 PM, Hadouken said:

Just do what you did in europe then

tools are in Europe hence why he need's somewhere who can do it.............. and a generator is a little different to a skyline engine. if you feck the gen up nobody cares, i break his skyline he will cry!

anyone ever had it done by a mech?

to be honest even if i could borrow the tools i wouldn't feel confident.... we used to fill the hole with a rag forced into the top of the cylinder with the piston at tdc, once it was tapped we would vacuum out, remove the rag, vacuum again, then use a tiny fiber optic camera with a light to look for the fillings. it used to work. anyone confident enough to do this around the peninsula?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If you grease up the tap it should hold most of the chips in the flute, I'm guessing the thread only needs a cleanup anyway, as if the plug were fully cross threaded it would need to be removed and helicoiled.

A vacuum cleaner with a length of hose attached sounds like the go for cleaning out the bore, and those snake cameras are only $100 these days.

I doubt that is the cause of the missfire though...

533 RYC Proficient

533 RYC

Posted
Posted

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

it doesn't seem to bad. its at a very slight angle, towards the front of the engine, i say i think its misfiring but not actually sure car drives perfectly, but we changed the knackered coil packs, and the one on that spark plug was cracked, and it seemed like it was because of the angle it was attached.its not a major issue, but its just gonna cost a fair bit if it keeps cracking coils.

cheers for all the input fellas, we just really dont have the tools or equipment to do it ourselves. rather pay out 100 bucks or so rather than having to forkout for a new head/gasket/ancillarys etc.

Plattsy Grand Master

Plattsy

Posted
  • Author
Posted
  On 20/07/2012 at 2:20 AM, 533 RYC said:

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

shame your in sydney boss, otherwise we would be round with some beer for ya in exchange!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...