Jump to content
SAU Community

Recommended Posts

Hey guys,

So I have been searching the interwebz about all the tricks to find Vac Leaks.

I also searched SAU and found a few threads with mixed ideas and some of the exact same info.

So most people they say spray it with carby cleaner or start ya bast.

This I guess is a good/bad idea for larger leaks which can be pin pointed by spraying it around and listening for a change in revs.

I have tried this method on my vac leak but still come up with nothing.

Now in my searches people have also used smoke machines to find leaks and there are 2 types you can get either the party ones or the expensive ones made for cars.

Others on youtube have even just used a cigar and a long pipe!

Anyone have any experiences with Vac leaks.

Have you found it?

How did you find it?

Did you use a party smoke machine?

Did you take it to someone for them to find it.

I am considering going down to the party shop and buying myself a smoke machine but then the glycerin worries me having it inside my vac lines etc.

Link to comment
https://www.sau.com.au/forums/topic/406123-vac-leak-tip-tricks-hints/
Share on other sites

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Easy and cheap way man. What size is your intake pipe, 3"? Assuming it is; buy a 3" straight joiner, a 3" cap that fits snugly inside the joiner (I bought mine from Bunnings), and head to your local bicycle store and buy a valve stem for a tyre. Then what I did is used a soldering iron (if it's not an old one, make sure you clean it up afterwards) to melt a hole in the plastic cap and pushed the valve stem into it.

Remove your AFM from your intake pipe and clamp your newly made device on in it's place. Then if you don't have a compressor you can buy one of those $11 portable ones from Supacheap, attach that to the valve stem and pump away listening/feeling for leaks. Make sure you're not pumping 250psi through it, but it should struggle to make even 2psi.

That whole setup cost me about $20, but I already had a compressor. Hasn't failed me yet :D

Might check out a regulator so I can make sure it only pumps around around 2psi.

So this way should make it the whole way to the intake plenum?

Sounds like a good idea because there is no need for smoke or anything.

More then happy to try this tonight.

Anyone else have any ideas.

Just want to get as much info to help other SAU people out if they end up searching this.

Sometimes the joiners only leak when hot, once they soften up. It's a good idea to go over every clamp while its hot on the dyno or after a drive as you can get more turns on the worm drive.

I ran mine and a mates STI liberty up to 40psi with the alloy 3 inch bung I made, there were all manner of leaks. lol.

Hanaldo is this what you did when you had the issue with your intake

Nah man, didn't end up needing it. I've used it a few times before though, it's very handy.

You shouldn't need a regulator as the compressor should have one, just keep an eye on the gauge to make sure :thumbsup:

I went over all the clamps

Even spent the past 4 days putting a new intake manifold gasket on and that still didnt fix it.

Cant wait to knock off work and go put this together.

All else fails im going to buy a cigar and blow that f**ker like a $2 hooker

Pretty much what I did too Hanaldo. the best part about this method is that the engine aint running and you can actually hear, see and feel where there leaking from.

I used an old shiny cricket ball jammed in a joiner just before the throttle body and pvc fitting with a hole drilled into in the intake before the turbo . (PS make sure you clamp it though. 25psi behind a cricket ball with a nice big intercooler fires a cricket ball out damn fast!!!)

Pretty much what I did too Hanaldo. the best part about this method is that the engine aint running and you can actually hear, see and feel where there leaking from.

I used an old shiny cricket ball jammed in a joiner just before the throttle body and pvc fitting with a hole drilled into in the intake before the turbo . (PS make sure you clamp it though. 25psi behind a cricket ball with a nice big intercooler fires a cricket ball out damn fast!!!)

So I guess you must have thought the leak was before the intake then.

Why didnt you just let it go all the way into the intake

So I guess you must have thought the leak was before the intake then.

Why didnt you just let it go all the way into the intake

Well the engine is an air leak itself, which is why I said you will struggle to make it hold a lot of pressure. But you should still be able to find where it is coming from.

If you don't find anything with it going through the intake, try the method urtwhistle used, might help.

i have had a leak in the intake manifold, i found it by spraying all the gaskets with wd40, if its not leaking it just drips, if its leaking it sucks it in while idling, when its on boost, you'd need a dyno and that is when it will spray outwards ..... this is for the intake im talking.. and this info was given to me by DVS JEZ and im so greatful for his input cause i was confused bout it for months... again thanks mate... :yes:

Well I had oil sprayed on my strut tower which was directly opposite the intake manifold.

So I cleaned it and went out for a boost and it was there again.

But at idle and spray with start ya bast it didn't get sucked in at all just dripped.

I replaced the gasket now the oil has stopped but the squeal on boost is still there and there is a whistle when sitting on -45 vac

That's why I was thinking of doing the pressure test rather then spraying stuff over and over

well i had the noise on boost, and the spray sucked in on idle, hmm it will only get sucked in on a vacumn

the whistle is normal with turbo's i think depending on the turbo, but maybe you have a leak on the exhaust side as well? do you have the tags on the 4bolts that connect the turbo to the manifold?

does the car idle smoothly? cause mine was a pig and wont start now , so im doing the gasket and im about to check if the manifold is warped a bit too..

I can't get the idle correct no matter how much I play with it. So that's why I'm down to it being a leak.

The whistle only happens around -45 vac on my greddy profec. You can hear the turbos spool but it's a totally different sound and is only recent.

And the high pitch squeel comes around 15psi and wide open throttle

The tabs should still be there because we did them when replacing the turbo but I'll try to suss that out as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
×
×
  • Create New...