Jump to content
SAU Community

Recommended Posts

Hi,

My mechanic has identifie my water leak to a corroded metal pipe with a couple of connections for coolant/heater, its located under the intake and I think it runs parallel somewhere between near where the thermostat is located and towards the firewall, but cant be sure as I didnt pull it apart. He's sent me a pic (attached), and I need to find a replacement or at least the name of the pipe so I can track one down. Cars off the road until I find one.

Anyone can identify and point me in the right direction on getting a replacement would be awesome :)

cheers

XYSMK.jpg

Cool, possibly could be. Like I said, haven't seen it myself where it came from, only this pic :)

He said one end comes from a fitting on the block to a short rubber hose to this cross section. It's a joint with each end being 3/4inch, one side has 5/16in and other 1/2in connector. Hopefully means more to you than me haha

  • 3 years later...

I'm in need of the same part as well as a few others. Only thing is that mine is a Stagea and the diagram doesn't seem to have that part.

Mechanic said he was also after the 2 Circled parts plus

1* metal pipe connector

2* plastic fittings

1* Inlet Gasket

1* Plenum Gasket.

Can anyone please help...

post-18088-0-23835900-1460963906_thumb.jpg

Edited by wagon

For an ECR33 the part number is 1405321U00 and on my invoice its called PIPE, WATER-OIL COOLER .

They are only available ex Japan and mine came via John Robinson Nissan Rockdale in Sydney .

I ordered everything under the manifold hose and tube wise that see's coolant including the screw in rear block fitting and the press in water pump end one and the longer tube that hangs under the manifold .

Search ECR33 followed any of those part numbers on the Nissan diagrams . Brings up an American site with the schematic and actual part numbers .

A .

Edited by discopotato03

I think i have confused myself. Not non turbo but series one. The part looks as if it is that part in the op's pic above but that doesn't seem to be on a series one (96 model)

#http://nissan.epcdata.ru/stagea/wgnc34/5411-rb25det/engine/211/#211C_002

Seems an awful lot more parts on the later models?

  • 1 year later...
8 hours ago, Mooglymoog said:

Bump. I need this weird fitting for an RB 20 DET red top. Does anyone know where to get one? Part number? I found a diagram and I think it is 14020HA or something. 

post a pic of what you need, i probably have one

I actually just took off my lower runners and have the same exact issue with mine as the first post. Quite honestly I was thinking of just cutting the rotted metal part out and securing the new hose to whatever is left.

Although I've had no luck with diagrams as of late so if anyone has part numbers I'm sure there's some interchangeable parts between the 240SX/300ZX heater hose wise. It'd be nice not to fork over $300+ for a hose kit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...