Jump to content
SAU Community

Shout Out To Scotty Nm35 - I Have Boost Again!

ドッミ

By ドッミ,
in Four Door Family & Wagoneers

 Share

Recommended Posts

ドッミ Newbie

ドッミ

Posted
Posted

A big shout out to Scotty NM35 for all his help and skinned knuckles with the removal and install of my turbo!

New shorter core produced quite a few install issues and problems for Scott along the way. But he endured and I have boost again!

Coupled with a 'Scott Dump Pipe' and actuator mod, there is a definite extra kick.

Thanks so much Scott. Love your work.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

No problem Dominic, glad to help. Did you get underneath and check it out?

Not very happy with the way this turbo was installed, too many mods required to make it a feasible option. That said the stock like response felt good for an untuned engine.

You are lucky I waived the bandaid tax, costs could have blown right out. :)

Sunkist Grand Master

Sunkist

Posted
Posted

Welcome Dominic

Yeah, I hear Scotty does OK work :)

What turbo did you get?

Cheers, Leon.

Lol ok? There were SOOO many problems Scott had to fix after getting the turbo back.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

iamhe77 Grand Master

iamhe77

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

Sounds like the same issue that Craig had when his 3071 highflow went on.

Sunkist Grand Master

Sunkist

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

Pick up yo phonnnneee nigggahh

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Sounds like the same issue that Craig had when his 3071 highflow went on.

Exactly, even though I was promised it would fit as he had already sold two of them. It's easy to fit when someone else is doing the work though.

ドッミ Newbie

ドッミ

Posted
  • Author
Posted

No problem Dominic, glad to help. Did you get underneath and check it out?

Not very happy with the way this turbo was installed, too many mods required to make it a feasible option. That said the stock like response felt good for an untuned engine.

You are lucky I waived the bandaid tax, costs could have blown right out. :)

Haven't had a chance to climb under and look as yet... Got home from work in the dark yesterday, then back here this morning in the dark! Things one has to do to pay for repairs to a shagged M35 turbo!

Really impressed by the acceleration. As you said, close to stock. Very linear and coming on from approx 2500rpm with the extra kick.

My original post certainly didn't describe just how much stuffing about you had to do. Word of warning for anyone else going down this path... Speak to Scott and he will say, DON'T, I am sure.

Thanks for waiving the bandaid tax - with the number of cuts suffered, the cost would easily been higher than the value of the car!!

That was a mighty big look of relief in the rear view mirror, when I drove off - clearly happy to see my car disappear!

Sunkist Grand Master

Sunkist

Posted
Posted

That was a mighty big look of relief in the rear view mirror, when I drove off - clearly happy to see my car disappear!

relief?

hahah he was probably pissed off that he had to start mine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...