Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

I'm going to a bench press seminar tomorrow hosted by Nathan Baxter at my new powerlifting gym. Very excited, but also not sure what to expect. I'm hoping to learn some tips and tricks; possibly readjust my technique as I have issues with keeping my knuckles pointing to the ceiling, and get back to my pb anyway! :)

just realised your post was old. how was the seminar?

Hey Nick, it was amazing. Nathan Baxter is a huge wealth of knowledge and quite funny!

He pointed out my bench grip is too close together and I'm using a lot of my triceps. At first, the wide grip felt horrible and I couldn't bench 40kg without help from my spotter. However; after a few goes I was easily benching 42kg for reps. He also gave me some great tips about crushing the bar on the way down, and focusing on keeping the pinky finger tight!

I got the most of the deadlift tips and tricks though. An important technique he taught us was breathing in and pushing out your stomach before lifting. I don't have much of a stomach to push out, so he suggested I use a belt. I'm also having my knees too far forward in my setup; hence all my knee bruises. He suggested when I set up to keep my legs straight as I bend down to touch the bar; only once I have touched the bar with my hands should I bend my knees. He had some great cues, which I think will be beneficial to me once I'm used to them. Deadlifted a pb of 102kg at the seminar anyway :)

I have now joined Dungeon Powerlifting in Bunbury, WA. I have my run through and programming session with the strength coach tomorrow. Hopefully you will be seeing bigger numbers out of me soon!

its amazing how much difference a proper set up from the top down can help your deadlift. I still need a fair bit of work on my technique which is why im going to join PTC canberra in january. Hopefully all 3 of my lifts benefit a bit.

  • 2 weeks later...

PTC don't do speed/dynamic days

All good Mitch, just means your getting nice and tight and using leg drive. As you get stronger you'll be able to press the same amount and keep your ass down.

Also squat more = bigger ass... harder to get it off the bench! haha

  • Like 1
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...