Jump to content
SAU Community

Recommended Posts

i've had some falken ziex tyres in the past. not sure if exactly the same ones, but i know that they were the worst tyre i've ever driven on in the wet, even when relatively new.

so i'm guessing that it's a mix of shit tyres and going too fast into the round about.

before i got new tyres on my wagon i could go into a wet round about at about 35kmh, light constant throttle and then just use the steering wheel to get the back out should i so choose to. all it would take is a small sudden adjustment. all it would take was moving my hand from say 5 o'clock to 6 o'clock.

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

My 2 cents:

  1. Running 265's in the rear and 235's upfront is a significant offset difference for the wheel track. This needs to be compensated for in your driving style. But by the sounds of things you don't have a huge amount of skill.
  2. I think you're running too much negative camber in the rear, the tyres look okay, but I can see more wear on the inside, this means that you do not have the maximum contact patch when cornerning.
  3. When you approach a corner, do you have what is known as "viscious turn in"? I do get a little hardcore on the turn in when I want sideways action, or when I am getting over zealous at the track. Try to be smooth with your steering inputs.
  4. Slow in, fast out. Great words that should be applied to every corner.
  5. Are you taking into account the camber of the road when cornering. Negative effects of camber on corner ability are amplified in the wet.
  6. Wet roads (especially freshly wet roads) are usually very oily as well.

My advice:

  1. Get suspension setup properly
  2. Drop to a 255 rear end, unless you seriously need 265's for traction, don't go any wider than you need to.
  3. Do a defensive driving course, then a track day.
  4. Never ride a motorbike, shit will get ugly in a biblical way

advice noted , with time I will do all of the above

So, treadwear 360, old, and Ziex are known to be crap (not surprising at treadwear 360!). Strong evidence your problem is that the tyres have no grip.

wtf is treadwear 360?

Did anyone notice the manufacture date of the tyres? End of 2008.

How long ago did you buy the tyres?

I try to buy tyres that are no older than 6 months since they were made.

i've had some falken ziex tyres in the past. not sure if exactly the same ones, but i know that they were the worst tyre i've ever driven on in the wet, even when relatively new.

so i'm guessing that it's a mix of shit tyres and going too fast into the round about.

before i got new tyres on my wagon i could go into a wet round about at about 35kmh, light constant throttle and then just use the steering wheel to get the back out should i so choose to. all it would take is a small sudden adjustment. all it would take was moving my hand from say 5 o'clock to 6 o'clock.

same , just a slight twitch of the wheel was all it took for all hell to break loose

So, treadwear 360, old, and Ziex are known to be crap (not surprising at treadwear 360!). Strong evidence your problem is that the tyres have no grip.

a

h , didnt know ziex where known to be crap

Kumho ku36's then?

again , whats treadwear 360?

Tread wear rating is what the tyre manufactures use to rate the hardness of the rubber, higher the number the harder the tyre (in general terms)

hmm google is our friend....so apparently treadwaear is completely relative to each manufacturer..ie only allows you to compare among the same manufacturer not across all brands

in anycase , nice bit of info to know.

oh well , ku36's all round then.

hmm google is our friend....so apparently treadwaear is completely relative to each manufacturer..ie only allows you to compare among the same manufacturer not across all brands

I dont agree with that. While there are issues with treadwear as a measure, its still a useful ballpark indicator across brands.

Here's some numbers i just made up;

<40 = slicks

60-100 = r spec

140-200 = s spec

200-300 = street tyres

300+ = long life street tyres not much grip

As a gross generallisation, low treadwear is associated with good grip and short life, and high treadwear is associated with long life and poor grip.

ok its the tyres

if you look on the Tyres you use(d) and how u would rate them youl see that the ziex comes up again and again as so bad in the wet that its dangerous...

f**kn hell ,how are they even allowed to sell tyres this dangerous? It rained again tonight , took it really easy but I could feel the tyres where starting to lose grip.

I put my foot down ever so slightly when at the lights and the rears started to spin on the spot. Camrys and kias where taking a corner way faster then me and most where overtaking.

This tyre is so bad its embarrassing, there should be a sticky in the tyre section to never ever EVER EVER EVER purchase any Falken Ziex of any model.Ever. F*ck you Falken.

Edited by tripsteady

I empathise with you.

I once bought some wheels for my 4WS VTiR Prelude. They were shod with Nankang S Sh!tt

Anyway, on a wet night, I followed a Vectra (FWD) around a sweeper at 50Km/Hr and my car lost all traction. The tyres were near new. I thought WTF.

I went to Blair's Tyres who are agents for Nankangs. Nankang Aust branch was very obliging after checking the date on the wall.

They were so kind, they gave me a brand new set of the same tyre that slipped just as badly on the next wet night !!!

If I had looked in the rear vision mirror as I took off, I wonder if I would have seen some tyre man 'crossing' himself?

I empathise with you.

I once bought some wheels for my 4WS VTiR Prelude. They were shod with Nankang S Sh!tt

Anyway, on a wet night, I followed a Vectra (FWD) around a sweeper at 50Km/Hr and my car lost all traction. The tyres were near new. I thought WTF.

I went to Blair's Tyres who are agents for Nankangs. Nankang Aust branch was very obliging after checking the date on the wall.

They were so kind, they gave me a brand new set of the same tyre that slipped just as badly on the next wet night !!!

If I had looked in the rear vision mirror as I took off, I wonder if I would have seen some tyre man 'crossing' himself?

lol , its not a good feeling losing traction when you dont expect to....Im avoiding the rain until I get my new tyres. Hoping i get can my hands on some toyo t1rs.Have only heard consistently good things about them.

question, is this turning left or right on a roundy or just going straight through?

Stiff suspension, lots of camber/bad alignment and hard tyres could be causing this problem.

^^as above

also when lowering a car you'll get more wheel spin off the line as there is more neg camber on the rear meaning less tyre to the road. try lowering you tyre pressure to 30 or so for more rear grip

when its raining next i recommend you get out to your local free drivers training area and practice a low speed donut

best road tyres I've ever used are toyo t1 r/s + pirelli p zero nero, pricey f**kers but.

Also used Kuhmo KU36 pretty decent tyre for the price but I found they wore down pretty quick compared to the above

You're better off getting a set of Bridgestone Turzana tyres which will be better in the wet and are more of a grand touring tyre than the KU36's.

KU36s are extremely good in the dry, and not that great in the wet.

You're better off getting a set of Bridgestone Turzana tyres which will be better in the wet and are more of a grand touring tyre than the KU36's.

My old man has these on his Mazda 6 and dare I say it it grips a hell of a lot better than my 32. they feel really safe in the wet, but for the price you are probably better off getting more of a performance tyre.

I run KU36's but because I don't drive the GTR that much in the rain.

You're better off for a KU31 as a street tyre. KU36's are really designed to be a high performance street which means it will be better in the dry than wet. The KU31 is more all rounder.

Also the NSW club get's federal 959ss and RS-R's for bloody cheap on our member price. You'd probably save the membership fee on a full set with change to spare.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • (Rb25det intake manifold) I’m having a hell of a time trying to find the full part or part number of this coolant hardline so far I was given these (Below) but they aren’t what I’m looking for and was told it’s the IAR or aac valve but that doesn’t seem to be it either. If someone could point me in the right direction it’d be greatly appreciated. Or if anyone has it for sale that’d be great too. I have recently purchased a greddy manifold and I can’t seem to find my old one to pull it off.  (Front Heater Return / Water Pipe (under intake): Primary part: 14053‑21U10 (front return pipe assembly for R33/R34 RB25DET) Alternative listing: 14053‑21U00 (same pipe, sometimes interchangeably referenced)   Heater Feed Pipe: Listed as 14075‑04U00 or feed-related variant 14053‑AG500)    
    • This sounds cool. But, as per usual, anything really complicated like that, that I take on, constitutes a steep learning curve that I never actually "learn". I just get it working, install it and start using it. Then, when it breaks a few months later, I've got no memory of what I did, how I did it, or even the bloody IP address I gave it. I'm having more or less exactly that problem right now. My Proxmox machine was discovered to be non-responsive, and the VMs on it were ditto. Power cycle it to a stream of loud Dell beep codes - which was unpopular at midnight, I can tell you. Move it to the lounge room so I can HDMI it to the TV for a screen, see the boot messages complaining about the /PVE/data having all sorts of LVM problems, saying it needs to be fixed manually. And I'm like....great. How am I going to work out what I need to do? At least it wasn't the stupid Silicon Power SSD shat itself. Mental note for all readers - DO NOT BUY SP SSDS! They are shit. I have had one take out an entire VM setup already, and this one could have done the same. Maybe it actually has. Cheap Chinesium shitbaskets. I won't cheap out again, even on play projects with no budget. Because my time budget having to fix shit is worth far more than the cost of proper parts.
    • I do typically agree. These days even the screens most people use have more of a boot time than the main device. However, I've seen an interesting use of the RPi in vehicle, however it involves effectively building your own OS and MBR, as then it boots up exceptionally quickly, as you don't have everything needing to start up, and you can then also run it up as an RTOS, while still having more compute than an Android can give for things like display, and processing. A very huge task that would be though for Duncan, I'm not sure that's his skill set (or Arduino programming and wiring) ha ha. If end goal is definitely just water cooling, Arduino would be the simpler setup especially for a rookie. If he wants extra display stuff though, bashing some code in Python on an RPi may be the better result for both systems.   Unfortunately the new device I'm building at work which runs a display, is too slow of a display for dashboard style purposes. More extreme low power, update only a couple of times a day type system
    • I don't like "actual computers" for in car use. They take time to boot up, have OS annoyances, and so on. Arduinos etc are ready to go a few seconds after power on, don't mind being agressively powere cycled, because everything is non-volatile, don't mind being shaken and stirred.
    • As Fred would tell us, it's all about interpreting the rules. It's not a water sprayer, it's a water mister... But everything else you've said, 100%! Even a raspberry Pi would be great, use HDMI out for a display, and add a raspberry Pi CANBus hat to read values out from the ECU.
×
×
  • Create New...