Jump to content
SAU Community

Recommended Posts

Good move, I don't regret installing it for one second.

The other great benefit is that the sensor will be installed in the correct location in the exhaust. This will give you a more accurate reading of the AFRs (when you get it tuned) rather than a sniffer in the tail pipe.

  • 4 months later...

I've done a fair bit of maintenance to fix a few ongoing issues over the last few months. The car now has all the rubber suspension bushes replaced with Whiteline/Nothalane. It also has a new air conditioning condenser, heater core and rear wheel bearing replaced.

Of note, my car has had an intermittent steering wheel vibration at around 100 kph, that I've been living with for as long as I can remember. It wasn't because of a wheel imbalance as I've had several tyres/rims over that period with the vibration always persisting. What fixed the problem was replacing the front inner/lower suspension bushes. My upper camber and caster bushes had been swapped swapped out for urethane years ago - so the lower ones were the last rubber ones remaining.

  • 7 months later...

Time for some updates... Pics of the new Aircon condenser and Heater Core that I put in...

IMG_1573_zpsaab65d22.jpg

IMG_1574_zps766dd430.jpg

I ended up reusing the plastic heater core fittings not the metal ones shown in the picture.

  • Like 1

I found that the bolts and washers that hold my MX Performance plenum top down onto the lower runners weren't really up to the task and the washers had deformed. So I ordered some titanium flanged hex head bolts to replace them.

IMG_2017_zps80d277c5.jpg

Out of interests sake, I wanted to know the weight saving, seemed like a good job for the wifes Thermomix!

IMG_1969_zps684c5b51.jpg

IMG_1971_zpsc461a104.jpg

So for around $100 thats an awesome weight saving of 100 grams! I'll only need to spend another $500,000 on titanium bolts and I should be able to get the weight of my car down to the same as a Lotus Elise! :blink:

Edited by Ryno

Since going to my new exhaust manifold setup the car has been a fair amount louder. I finally decided to tackle it back in November and swapped out the rear cannons and centre muffler with new Magnaflow mufflers.

Out with the old...

IMG_1973_zpsec5a538e.jpg

Rigging up the new...

IMG_1975_zpsc8a4337a.jpg

IMG_1978_zps50c15af8.jpg

IMG_1979_zps363a85dd.jpg

My latest drama to fix was a leaking Power Steering rack...

IMG_2464_zps1b042f11.jpg

I was able to swap it for a reconditioned rack that cost $350. But at the same time I wanted to finally fix a problem that has been bugging me for around 10 years!

Ever since swapping to the RB25DET engine and removing the HICAS I've been living with heavy steering as the power steering goes into a limp mode due to no speed input.

The solenoid on the power steering rack gives full assistance with 12 volts and the assistace reduces as you reduce the voltage. So I purchased this voltage step down module from Jaycar...

IMG_2482_zps433531ac.jpg

I have wired that direct to the Power Steering solenoid and can adjust the voltage as I see fit. It is still not going to be speed variable (like stock) however I can tweak the voltage to find a happy assistance that works ok at all speeds.

Checking the output voltage...

IMG_2483_zpsb87539a7.jpg

Where I've mounted it in the car...

IMG_2484_zpsd066444c.jpg

Edited by Ryno
  • Like 2

Thanks Glyn, yeah I'm very happy with the exhaust... it looks the business and the sound has reduced nicely while still maintaining the unique note from the twin pipe setup.

Edited by Ryno

Yes I've been driving it to work every day this week. At the moment I have it set on around 8 volts and the steering is nice and light.

I'm just a bit frustrated that I've only fixed it now... It's such an easy solution, why the hell did I put up with crap steering for 10 years!?

  • Like 2
  • 2 weeks later...

Yes I've been driving it to work every day this week. At the moment I have it set on around 8 volts and the steering is nice and light.

I'm just a bit frustrated that I've only fixed it now... It's such an easy solution, why the hell did I put up with crap steering for 10 years!?

hey ryno

i have a 93 r32 gtr that still has hicas but occassionally has heavy steering at low speeds/parking. Can the above solution you put in place be useful for my situation?

Jase

Absolutely... all you are doing is intercepting and controlling the voltage going direct to the power steering rack. It's a very simple and effective fix.

fantastic ill keep it in mind if it continues to play up. Its been bugging me. Would you consider doing a diy write up?

fantastic ill keep it in mind if it continues to play up. Its been bugging me. Would you consider doing a diy write up?

I've just done up a DIY for the power steering fix, once it is approved by the moderators I will provide a link.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...