Jump to content
SAU Community

Recommended Posts

Hello any help would be great,

My C34 is currently leaking oil from near the oil filter, I'm 99% sure its not the oil filter because when i grab it with clean hands the filter and the filter block are clean. It looks like its coming from the part in the pics iv attached it might be the factory oil cooler? not to sure just wondering if anyone knows of a common leak that can develop in this area? I cant get a good look in there and I have big hands LOL, also its leaking a fair bit of oil so I need it fixed asap.

thanks guys

Rhet

post-56886-0-99762900-1348377090_thumb.jpg

post-56886-0-96705600-1348377121_thumb.jpg

post-56886-0-98867300-1348377156_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/409953-rb25-oil-leak/
Share on other sites

That's an iunisual place for an oli leak, the cooler is a bolt on arrangement and unles you have removed it there sholud be no problem, how much oil are you loosing it might be coming from above, cam covers are prone to coming loose, try tightening the covers maybe.

Link to comment
https://www.sau.com.au/forums/topic/409953-rb25-oil-leak/#findComment-6546557
Share on other sites

I have a remote oil filter in which I have oil temp and oil pressure sensors for dash mounted gauges. I run single din and gauges fill space.it is cool and practical.No leaks.

Link to comment
https://www.sau.com.au/forums/topic/409953-rb25-oil-leak/#findComment-6546593
Share on other sites

It is loosing a bit, a little 10cm puddle when I park over night. It has never been removed as far as I know. I did look to see if it was coming from higher and didn't see anything but I'll have a proper look tomorrow again.

Link to comment
https://www.sau.com.au/forums/topic/409953-rb25-oil-leak/#findComment-6546840
Share on other sites

  • 1 month later...

Hello again fine sirs! after repairing the first oil leak i have found another, oil is seeping from the very front of the sensor to the left/below the oil filter. Right from the front just behind the screw that holds the tab/electrode thing for the sensor wiring. Now is this the oil pressure sensor? i'm thinking it may be best to replace the whole thing? any advice?

cheers guys, this is really starting to shit me!

post-56886-0-04450000-1352018130_thumb.jpg

Edited by horrace
Link to comment
https://www.sau.com.au/forums/topic/409953-rb25-oil-leak/#findComment-6608819
Share on other sites

Agreed with Dale. Hey Rhet, does your oil light on your dash work? I was wondering from viewing the first pic why it was disconnected. That brown plug flappin' in the wind in the pics should most likely be connected to it..........

Link to comment
https://www.sau.com.au/forums/topic/409953-rb25-oil-leak/#findComment-6609172
Share on other sites

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...