Jump to content
SAU Community

Recommended Posts

Hi everybody

After seeing so many stags stolen I thought i might see if anyone is keen on a jaycar GPS tracker

I work for jaycar and can get damn good group buy pricing on GPS trackers

+8 pricing is approx $110, single unit price is $150

Here are the specs if anyone is interested i may organise a group buy PM me if you are

GPS/GSM Tracking Device

A GSM and GPS Tracking solution to locate and track the whereabouts of your vehicle in real time via the Internet on a computer or Smartphone. The device is easy to install with only 2 - 4 wires to connect. Insert a GSM Sim card (not included) and hide the device away on a metal surface or carpet using the included hook and loop adhesive. It works by sending the vehicle's GPS coordinates via the GSM network to the free online tracking service, which shows the location on Google Maps. It can also SMS longitude and latitude coordinates to up to 3 mobile phones, as well as alerts when vehicle exits a pre-determined area or exceeds pre-set speed.

Other features include an engine kill function to remotely disable the petrol pump, and movement sensor to extend battery life. An SOS/Panic button is also supplied which can send an SMS to the pre-programmed mobile phones. The built-in rechargeable Li-ion battery will keep the device functioning for up to 4 days when power is disconnected, which could help you locate the vehicle should it have been stolen and abandoned.

There is no installation or on-going tracking charges. You only pay for the GSM sim card and service. Supplied with wiring loom, installation and operation manual.

Please Note: This tracker is compatible with 3G SIM cards , however it only operates on a 2G band .

Features:

• Real time upload current location to website

• Turn off car engine by Internet platform or SMS for Anti-theft

• Listening sound around tracker with silence by SMS or platform.

• No platform Service charge (Our free tracking platform)

• SIMCOM GSM module (Quad band)

• Upload interval is 30 seconds according the setting of tracker

• Built in shock sensor to control GPS on off to extend battery life

• Shock sensor can be used as car shock & movement alarm

• Website shows history tracking

• Platform uses free Google Maps

• Send alert when vehicle exits a restricted area

• Send alert when vehicle exceeds the restricted speed

• Power supply disconnect alarm

Specifications:

• Data Usage: 0.07KB every 30 second upload interval

• Normal operating temperature: -20 to +55°C

• Restricted operating temperature: -35 to +70°C

• GSM Frequency: 850/900/1800/1900 MHz

• GSM & GPS Antenna: Built-in

• GPS Channels: 32

• Locate Accuracy: 5 ~ 10m

• GPS Start Time: 1sec (Hot start), 36sec (Cold start)

• Standby current: 1 - 2mA

• Tracking current: 35mA

• Operating voltage: 12 - 32VDC

• Charge voltage: 5V

• Battery: 800mAh Li-ion

• Unit dimensions: 68(L)x48(W)x20(D)mm

Link to comment
https://www.sau.com.au/forums/topic/409965-eoi-jaycar-gps-tracking/
Share on other sites

I believe this should be in the General Automotive section as it isn't really stagea specific. Alot of Nissans have been stolen recently.

Do you have any screen shots of the tracking system or photo of the product? How would this pair up to the Mongoose VT404?

what would be the average ongoing cost of the sim cards?

On going costs would be by which ever plan you chose. The sim card is not included and you have to go sign yourself up with a carrier and just pop it in.

what would be the average ongoing cost of the sim cards?

Google 'long expiry' phone plans. Most discount resellers use Optus network so you need to be sure there's coverage where your car will normally be stolen.

The first plan I saw was $15 for 6 months.

That plan makes no sense.

$1/month, but minimum first month charge is $41, and you must have a minimum of $20 in your account at any one time.

So why is the first month $41?

That plan makes no sense.

$1/month, but minimum first month charge is $41, and you must have a minimum of $20 in your account at any one time.

So why is the first month $41?

$1 monthly fee

$20 for the sim card

$20 deposit

Then you just pay $1 month... Works out to be $1 per week really

$1 monthly fee

$20 for the sim card

$20 deposit

Then you just pay $1 month... Works out to be $1 per week really

$20 Deposit in case your car is stolen and you lose the sim card. (obviously they want it back @ some stage?) lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...