Jump to content
SAU Community

Recommended Posts

My 96 rs4 stag has had a problem since I have brought it , driving specifically between 85-115kph, I would estimate, I have a shuddering or 'pulsing' sensation coming from what I believe to be the rear axle of the car. Like additional torque is being applied to the rear driveshafts momentarily in an on/off fashion. I would say that it is not a reducing speed sensation, as in abs acting on the rear wheels for some even more bizarre reason, especially as it only happens at a light load throttle position and the sensation is destinctly coming from the rear end. Also it only seems to only happen when it's been running for a while or fully warmed up. Anybody got any suggestions or ideas as to what could be causing this to happen?

Link to comment
https://www.sau.com.au/forums/topic/412934-stagea-100kph-pulsing-shaking/
Share on other sites

Is it an awd car? Are all your tyres the same size and type? Tried turning left and right and listening for wheel bearings? Jack the car up and have a look? Wheels binding (foot or handbrake)?

Is it an awd car? Are all your tyres the same size and type? Tried turning left and right and listening for wheel bearings? Jack the car up and have a look? Wheels binding (foot or handbrake)?

Yeah it's awd and yeah all same tyres and same size. I can't hear anything while I'm driving. And it doesn't feel like anything binding up. Like I say it only really starts happening after driving for 20 mins or so and can only notice it at higher speeds

But thanks for your suggestions

Will be rest tyres are worn slightly more than the fronts

Mine is doing it ATM so I have had to make it rwd till I sort out new tires

Funny thing is that they aren't even that worn but the fronts are brand new

First up, I'd get the wheels balanced. This will shop up 90% of your problems. If the tyres are unevenly worn, the tyre shop will tell you (they like to make money). Uneven tyre wear can cause the AWD system to start sending torque to the front when it's not needed. If the rims are buckled or out of round, they'll tell you. The other thing it'll fix is unbalanced wheels.

I've had a vibration caused by all of the above.

  • 5 months later...

hhhhrrrmm sounds like my issue around 100 KM/S + -,the car shudders like it doesnt know what gear to select.

im about to have a shift kit fitted and oil changed ill let you know if this fixes the issue i think it is, which is oil thats lost its viscosity and causing the auto to do silly things. if it does fix this issue try sending a message to Jetwreck, he is doing all of my work as i cant be fkt, coz im lazy................... Actually I just read your sig and it says ur in Auckland and im pretty sure he wont go there unless you pay for it. but it might be worth asking him for a decent oil for your auto unless you know of one your self?

Edited by loymclure

I had this problem too, in my 2000 S2, really annoying and sometimes felt like the car was jerking back and forth at 80 - 100 km/h, turned out to be a really simple fix, check the attessa fluid level in the reservoir located in the back behind the inspection cover on the right hand side, make sure the engine is running as it will appear full if the engine is off, topped it up to the correct level with ATF/ power steering fluid, problem solved. Regards Craig

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...