Jump to content
SAU Community

Recommended Posts

got a few parts left over kicking about, as follows below

pics on request

r32 aircon compressor n mount $80

r32 a/c condensor and most lines $100

r32 gtst metal fuel tank $100

r32 gtr/gts4 atessa....sp? reservoir and lines $40

r33 hicas unit $50

r32 gtr rear sway bar $100

rb20/25 push type excedy heavy duty button clutch $500

near new 500-1000kms

3" split dump/front all in one with $50 worth of heat wrap $150

located VIC -SE

pm or post

Edited by Dan_J

good condition i presume, was removed from a wreck, not due to being faulty

also added

gtr/gts4 manual gearbox cross member and mount $80

rb20 auto tranny Free

might be the 5psd as it came out of a cefiro

s13 sr20 auto tranny free

  • 2 weeks later...

bump

clutch kit set me back $670 few months back

pics on request

also got

rear s13/r32 JIC coilovers -$150

height adjustable not damper with helper springs, one is leaking

  • 2 weeks later...
  • 3 weeks later...
  • 2 months later...
  • 1 month later...
  • 4 weeks later...
  • 1 month later...

10 AN turbo oil drain fitting from kando - $40 ------ $50 posted Aus wide

, awhile back bought the wrong one so got this laying around.

suit high mounted turbo or similar with stock oil drain bolt / hypergear.

from the thread start to end its 36cm, 32cm not including the thread on the nut thats crimped onto the braided line

you need to get an adapter to bolt onto the block to 10an

look like this but longer and no barb ( do have one to suit if needed tho)

$%28KGrHqZ,!qgE-y+Ppm%29yBPy+-ElHYw~~60_

  • 1 month later...
  • 1 month later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...