Jump to content
SAU Community

Recommended Posts

So my understanding of this thread is that this fuel isn't recommended for non daily driven cars?

My cars lucky to be driven once a month sometimes, would this cause the fuel to go off?

If you ran 98 it could go off... I don't know how you got that information out of this thread.

Yes, there is a chance the fuel could absorb water, so make sure you don't stick the hose in the fuel tank. :P

There was mention of fuel absorbing water and rusting injectors in non daily cars so just clarifying

I think you must have read what I wrote. Toshi tuned my car and when I asked about E85 he said its no good for a weekender (or less). I'm just going off what he said to me; water absorb = more chance of knock & potential to rust injectors if the car sits. I don't know anyone who's had that problem and I'm not going to let it worry me at all.

I'm tuning on e85 later this year because everyone seems to love the extra knock protection, lower EGTs, Higher power and it's readily accessible for me so why not!

i odnt no about E85 going off - i asked the same thing and he said he has a rally car that lives at the work shop and comes out jumps on the dyno for a check every 6 months or so or before meets and the e85 levels never drop and is still running after 5+ years of competing - - thats his experience anyway - i have just been told not to let it sit in plastic containers

I think you must have read what I wrote. Toshi tuned my car and when I asked about E85 he said its no good for a weekender (or less). I'm just going off what he said to me; water absorb = more chance of knock & potential to rust injectors if the car sits. I don't know anyone who's had that problem and I'm not going to let it worry me at all.

I'm tuning on e85 later this year because everyone seems to love the extra knock protection, lower EGTs, Higher power and it's readily accessible for me so why not!

My customer used E85 and he did not drive 2weeks then his car start engine knock (He could not hear knock but his ecu is power fc so he can see how many knocks).

He refill E85 then stop engine knock.

I think fuel pump and injecter is not problem.

I've had zero issues. If the engine is knocking on ethanol something is very wrong, mine will cruise on 20:1 without ping. Going by the PFC for knock doesn't sound very accurate...

Unless it was a bad batch of ethanol? I usually buy from high turnover servo's but I have never had an issue with this either. (and I have filled many hundreds of times)

Depends where you buy your e85 from

I've heard of a few united servos now having bad batches of fuel where the e85 has dissolved everything in the servo tank coming out like rust water blocking pumps and injectors to the point where the car won run

Caltex eflex haven't had issues ever

Is that what you run micko?

Sounds like they never upgraded the tank at the servo then, which is very illegal. Caltex would have the same issue with the old steel tanks, but they were obviously a lot more proactive with their rollout.

Yes mate been on eflex for ages with zero issues :)

Depends where you buy your e85 from

I've heard of a few united servos now having bad batches of fuel where the e85 has dissolved everything in the servo tank coming out like rust water blocking pumps and injectors to the point where the car won run

Caltex eflex haven't had issues ever

Is that what you run micko?

I was reading some yanky info on e85 the other day, and it mentioned that when installing fuel pumps in tank to insure that the terminals on the pumps and line had a non conductive cover or coating over them, because e85 is a conductive fuel and can short out in the tank and create fire.

Is that true I've never heard of anything like it before?

Exactly! Even if it did you got more power to drive away faster to extinguish flames :D

There is no oxygen in the tank, so no chance of a fire. Science! Anyway, my car exploding is of no concern to me if it goes faster :)

I was reading some yanky info on e85 the other day, and it mentioned that when installing fuel pumps in tank to insure that the terminals on the pumps and line had a non conductive cover or coating over them, because e85 is a conductive fuel and can short out in the tank and create fire.

Is that true I've never heard of anything like it before?

Lol. Mythbuster that shit. :P

The only way it becomes conductive afaik is when water is added. Probably best to just use the sealed Walbro 460L e85 pump to be safe.

I would think after 5 years on ethanol in my daily I would have dispelled most of the myths surrounding it, my car has not caught fire ever, the Walbro 255's are still running strong, and the fuel tank hasn't rusted away. I have also never cleaned the fuel filter... ;)

I was reading some yanky info on e85 the other day, and it mentioned that when installing fuel pumps in tank to insure that the terminals on the pumps and line had a non conductive cover or coating over them, because e85 is a conductive fuel and can short out in the tank and create fire.

Is that true I've never heard of anything like it before?

There is no oxygen in the tank, so no chance of a fire. Science! Anyway, my car exploding is of no concern to me if it goes faster :)

I am pretty sure there is oxygen present during installation of the pump.

I say plausible.

There will be air in the tank above the fuel but the vapour generally isn't as flammable in an enclosed space as people sometimes think .

The worry would be what was causing arcing across the electrical connections that may be exposed inside the fuel tank .

You'd think a pump drawing 18-20 amps would be more likely to do this than one drawing 8.6 amps .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...