Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Mine is a White 96 R33 GTR V-Spec. Got it from compliance about 2 months ago now and am loving it. Was stock from compliance, have since added:

18x9.5" BBS LM with 265/35 Yokohama ES100s

Reconditioned APEXi T-max coilovers with king springs (FR 400lbs, R 225lbs)

Cusco Caster rod

Cusco rear camber arm

Whiteline Front camber kit and pineapples

DBA slotted 4000 series rotors FR & R

Came with dual APEXi dual chamber BOVs but will probably remove those in favour of a set of stockies.

Time to liberate some HP!

black 92 r32,trust tdo5  turbos,18 x 9.5 racing harts , here is a pic courtesy of merli

You will give me your wheels (waves hand, Jedi style)

awesome.

white 1992 r32 gtr but seems to have all the specs of the 1994 model (pull type clutch, electronic hicas pump in rear of car instead of hydraulic in engine bay etc

Hey Amaru, what does the pump look like in the engine bay / electronic Hicas pump in the rear? What does mine have?

I've got a White R33 GTR which was stock when I got it. (and basically still is) I've added a set of Nismo Clusters and centre gauges and I've got a Power FC ordered (hopefully I'll have it by Xmas) and a set of TE37's which hopefully I'll get in a few weeks.

as my name implies i can only dream about owning a GTR let alone a gts-t at the moment. i've only been for a drive in one slightly modified gts-t and the grin didn't leave my face for days.........buying my first skyline after months or years of slaving, that expression will be priceless.

I just sold my modded 93 GTST Type M. I lost money big time but I have the goal in sight, a 1989 GTR from Japan. still searching at the moment. have missd out on 3 so far. hope to find one this week.

but then its a damn long wait. I'm driving a 1979 Dato wagon at the moment.

I work damn hard for what I have and just hope that no one ever says you dont deserve it.

Have you ever had someone say to you or heard them say you don't deserve that car?

just interested thats all. I have seen some nice cars with wreckless drivers and i have thought that.

cheer

mark

Midnight Purple 95 Vspec

2530's

HKS FMIC

HKS Dumps

OS Giken Twin Plate

Sard 700cc Injectors

PFC + HC + Boost kit

HKS Cam gears

Full zorst

Z32 afm's

K&N Pods

Nismo Fuel Pump

Nismo Regulator

Cusco Catch Can

18" Impul Hoshino Racing rims

Defi Gauges

big stereo

etc etc.

315kw at all 4 wheels on 1.3bar.

Cheers

Brett

  • 2 weeks later...

Mines a late model R32 GT-R (June 94 to be precise). White, with nismo sideskirts and nismo lower bootlid lip.

HKS suspension (very tough ride)

3 inch exhaust from cat back

17inch X 9 AVS wheels, Yokohama Grand Prix 255/40

Apexi Air (pod) Filters

Blitz Turbo Timer

Pivot Speed meter

HKS Cam Gears

Chip Torque Chip

Dyno: Max Power 233rwk @ 13psi

Quarter Mile: 12.84 @ 105.66mph

Drive it everyday and loving it!

I got a silver 1994 R32 GTR, its got ..

Tein type flex coil overs

Apexi pod filters

HKS front pipes

Trust cat back

DBA 4000 front brakes

WORK Termist 18x9.5 wheels

Rebuilt Standard turbo's with steel wheels

Apexi Power FC

HKS Cam gears

Cusco oil catch can

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...