Jump to content
SAU Community

Recommended Posts

You CUT

I sat and looked at her bleed green on the garage floor today. Drip.........Drip............Drip.

There was nothing I could do, :/

James have you been round with the cutter ??

i cut cut

i bought myseft some bolt-on's, miranda wouldnt let me put them on her..

2012-12-30143250.jpg

Looks good.

I didnt do anything because i decided to play hide and seek with my keys and spare keys. FUUUUUUUUUUUUUUUUUUUUU!!!!!!!!!!!!!!!!!

While your looking, I lost a set Honda keys last week. If you find them I'd appreciate their return - ta.

I think for guys it's called an extension, not a bolton.

But they look really good James.

Found them!!!!!

Looked in the same place so many times and they still magically appeared there when someone else looked :/

I made a template for my new airbox and started tidying up the engine bay! Will post a pic later

Found them!!!!!

Looked in the same place so many times and they still magically appeared there when someone else looked :/

I made a template for my new airbox and started tidying up the engine bay! Will post a pic later

Funny. I am thinking of making an air box soon too.

Should be titled what Sinister did ti my car today.

He brought my wing back to almost new and some other scuff marks on the paint with some buffing magic.

Also gave me a late Chrissy present.....Get your minds out of the gutter! LOL

Thanks Richard, your a legend mate. Much appreciated.

Finally got my ass of the couch and lowered my car so it doesnt look like a 4x4 lol. I think the lowest point is about 98mm so its pretty close to legal :)

20130101_203113_zpsefb11dc2.jpg

20130101_203117_zps57f0421c.jpg

Also cleaned up a few little bits and pieces in the engine bay. I removed the bracket that the injector resister pack attaches to and just mounted it to the chassis. Also relocated my FPR to the strut tower to neaten it up a little. Pretty dodgey pic but i couldnt find a camera lol. Still unsure of what im going to do with the hks grounding kit thats on it as it looks really messy (not that you can see it in this pic).

20130101_203207_zps8e319095.jpg

Edited by k_d

Drove the Micra to the coast on Monday, such a fun little car to drive.

Had to drive the Arse out of it to get back up the hill, so much fun with the dog sliding from door to door on the back seat.

Used 1/4 of a 41L tank from Dalmeny to here with aircon on alot. (not on hills).

I swear 70 of it's 79kw go on the aircon, flick it off and it's like hitting boost. LOL 1psi boost maybe???

Got home & started the Liner up for about a minute just so I could hear some engine. :D

Edited by Not a Pulsar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...