Jump to content
SAU Community

Recommended Posts

Just to do some basic fault finding pre auto electrician as the compressor engages when you turn it on but I am guessing the clutch in the compressor is buggered. Will probably need some info for the Auto electrician as well if thats the case.

Edited by thatlbeme

When you say the clutch is engaging, it must be audible?. Skyline clutches don't often wear down so I would assume its pumping. If your not getting any cooling effect then I would say its low on gas. If the compressor cuts out if the revs are above 2k for a few seconds this would confirm low gas. If the comp doesn't cut in/out then it will prob be low but maybe half full.

Start car, turn a/c on. Carefully check temp of a/c components in engine bay. The 2 lines going through the firewall should be cold on big pipe and hot on the other. If you can't identify them then the silver cylinder or maybe black on a r34 should be hot. Check and let me know

Any more info you have to help?

Edited by t_revz

The mechanics topped up the gas when they did the last service (done to keep the warranty legit) but didn't go any further with it as they only do the basics. The revs pick up when engaging A/C but thats as far as I have got. Downloaded the R34 manual but it doesn't cover the GTR but will use that as a guide to try and find out more. Might be outside for a while but will check the pipes you mentioned for coolness.

thanks

Edit, the diagnostics from the R34 manual seems to be applicable for the GTR as well, didn't find any faults when diagnosing and changed relays to check it as well so will leave it to the experts as it looks to be a magnetic clutch issue. The tubes from the compressor, the top one was warm and the lower one was normal when the A/C was on.

Edited by thatlbeme

If one was warm and the other ambient, then almost certainly its low on gas. One should be 60-70 degrees while the other around 0-5.

Low gas usually will have the cold one warm up as the gas reduces and at a certain point( about half full) the hot one will reduce temp until the pump won't turn on cos its too low.

Going to an auto sparky or air con shop they can put gauges on for you in 5 mins and should be able to diagnose it quickly and cheaply.

Cost of repair depends exactly what's wrong

If your AC is low on gas then it would be low on pressure also and stop the compressor from pumping. Unless your in line pressure switch is stuck on causing it to think the system is charged.

What is the actual problem? Are you not getting cold air through the vents. It could be climate control related or the rubber tube that senses air temp under your dash might have come off.

Just to do some basic fault finding pre auto electrician as the compressor engages when you turn it on but I am guessing the clutch in the compressor is buggered.

That statement doesn't make sense because if the magnetic clutch is buggered then the compressor wont engage. I've not heard of a case where the mag clutch engages but the compressor isnt driven. You should hear a loud click when the mag clutch engages. If it doesn't engage, it may be that;

1. the fuse is blown (which may in turn be due to the solenoid in the mag clutch breaking down and pulling too much current - you check that by measuring its resistance, will need to be 3.5 ohms if its the same as R32s). If you replace the fuse and it dies quickly that's likely the problem

2. not enough gas do trigger the pressure switch (as mentioned above)

I've not heard of a case where the mag clutch engages but the compressor isnt driven.

Usually when there has been a wiring fault causing the clutch to come in/out repeatedly every couple seconds the clutch will wear down. It will either stop being able to drive the compressor or it might drive at idle but upping Rpm will causing it to completely slip.

  • 12 years later...

Is the A/C compressor supposed to keep kicking in and the revs go up every so often as a result? (for a r34 gtt) Mine turns on roughly every 15-20 seconds if I remember correctly. I know on my other car it doesn't seem to do that but different car I guess.

I've had my car re-gassed and it still blows ice cold air after well over a year but have always had this happening.

Edited by silviaz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...