Jump to content
SAU Community

Recommended Posts

  • 1 month later...

Good to see your build is progressing.

It's a bit of a shame that you didn't end up trying a 1.5mm top ring. The results would have been interesting. I can't help but think there's a reason Nissan specified a 1.5mm top ring for the factory engine.

  • 1 month later...

Motor is back together and working. Some random thoughts.

1. Removed the back of head oil drain.

2. The oil cooler/warmer standard on an RB26 has got some weight to it. Removed that and replaced it with an RB20 unit (Thanks Troy). Running a filter with an oil relief in it now.

3. Drilling out the oil returns in the head is actually harder than people make it sound on the interweb. They are quite lengthy and the top is a little difficult to get to.

4. What I was told about the ring gaps in the old engine was a pack of lies - they were bigger than quoted.

I can relate with number 3. Cast is never very nice to drill, especially over great lengths. I think from memory I had to use long series 9mm drill bits. Then slightly blunten off the cutting edge so it was not so 'bitey' and want to pull itself through so aggressively.

What were the old ring gaps?

  • 2 months later...

Well the thing is back together and on the dyno. Problem now is it wont run more than 16lb for 410 horsepowers. Will run to 22 with the wastegate shut but the boost controller wont allow over 16lb. Bov's are fine. Actuators are HKS on -5 Garretts. Boost controller is a Blitz dual solenoid type. Any one with any clues?

Yes.

Tomei were my start point but I couldn't find a reference to an 86mm piston, only oversize ones.

Didnt look at ACL or Nitto (Not that the NItto list has an 86mm size anyway) because I didnt want to use them.

Have CP pistons currently and given the issues I have dont want to go back there either.

Nitto pistons are actually made by JE Pistons. Great bit of kit. They make custom items, so IMO, they are the best bet. If you know the size of your combustion chambers, deck height, and what head gasket you intend on running, you can order these with a custom crown / dish cc, thus giving you a custom and a lot more suitable compression ratio.

More info?

Does the power go up when you disconnect the WG and let it overboost or is it stuck on 410?

AFAIK it goes harder than 410 with more boost but I didnt ask for a number as I was short of time.

It was described to me as a boost control issue so the question is:

A set up issue with the controller - something stupid like hoses the wrong way about?

A component failure with the controller eg a stuffed solenoid of the twin solenoid controller?

Please note: I dont doubt the workshop those are just simplistic examples by way of um, examples

  • 1 month later...

Went to Collie on the weekend. For those who arent from WA it is a small country circuit which takes 50 seconds to get around. It is anticlockwise and if your engine is having oiling problems then Collie will show them up. Anyway the bottom line is there was no more than three drops out of the breather all day. So I am claiming victory and moving on.

Need to find a workshop now to sort the boost controller.

Good news! Do you think the tighter ring gaps was the main factor in reducing oil entering the catch can?

How about deleting the rear head drain? Do you think that had any bearing?

Good news! Do you think the tighter ring gaps was the main factor in reducing oil entering the catch can?

How about deleting the rear head drain? Do you think that had any bearing?

Honestly, no I dont any more. I did fixate on it for quite a while but the gaps in the piston rings I have arent at the low end of what people use and they work fine. I reckon its a combination of the Pacific Engine Parts rings and the CRC bore lube on start up followed by driving the thing immediately on engine start.

As for the drain, yes I pissed it off. Used the return in the sump as an extra vent for the blowby. Probably doesnt make a huge difference if your blowby is under control. Probably helps if it isnt.

Honestly, no I dont any more. I did fixate on it for quite a while but the gaps in the piston rings I have arent at the low end of what people use and they work fine. I reckon its a combination of the Pacific Engine Parts rings and the CRC bore lube on start up followed by driving the thing immediately on engine start.

As for the drain, yes I pissed it off. Used the return in the sump as an extra vent for the blowby. Probably doesnt make a huge difference if your blowby is under control. Probably helps if it isnt.

Glad to hear you have it under control!

I'll be interested to see how mine goes if/when I get down to Collie, venting the sump seems to make all the difference

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...